• LINDSAY L750D 30" cambio type ring debarker, LINDSAY 750R 6-tool rotor, 100 hp/880 rpm ring drive, updated hydraulic drives for in & outfeed arms, LINDSAY air seal & oil mist system, PFS 195 hp hydraulic unit, hydraulic infeed conveyor w/hydraulic driven hold down roll, hydraulic outfeed, tires, receiver & accumulator tanks, cab, controls, (11) new tool arms, spares, s/n: 39706

• (2) 66" insert tooth swing arm whole log cut off saws, 60 hp, clamp, in & outfeed log hauls, paddle wheel kicker, cab, controls, spare saws, parts

• 6' bar type package saw w/motor, 3 hp hydraulic unit

• 8-bin log sorting system w/(4) hydraulic paddle wheel type kickers, feed through log haul, steel sort bins, WGBM scanner tally system, computers, printers, ALLEN BRADLEY PLC SLC 5/03, sensors

• MONARCH D-530D 6' right hand 17ß canted, vertical double cut headrig, GE 150 hp/880 rpm drive, feed through rolls, shifting outfeed rollcase, controls, electrics, spare saws, parts, s/n: 5250

• SCHURMAN log boss 42"x12' right hand 17ß canted 2-knee Temposonic positioned carriage, (2) 2006 USNR upgraded spare knees w/upper & lower board dogs, BROWNSVILLE turner, (2) trucks, pantograph arm, bumpers, rail, PFS 100, 20 hp hydraulic units, controls, cab, spare parts, s/n: 180

• TYRONE BERRY SMA240 100 hp hydraulic carriage drive, 90 gallon reservoir, 3/4" cable w/tensioner, hydraulic unit, s/n: 41955

• Hydraulic log turner, 20 hp hydraulic unit

• LETSON & BURPEE DCH-1-V 6' left hand single band horizontal resaw, TOSHIBA 100 hp/1775 rpm, air strain, hydraulic wheel lift, PFS 25 hp hydraulic unit, BENSHAW 200 hp soft start, in & outfeed rollcases, controls, electrics, spare saws, parts, s/n: 1850

• SCHURMAN 6"-14" x 6'-12' sharp chain circle saw scragg w/(6) 36" saws, TOSHIBA 300 hp/1770 rpm, infeed centering rolls, outfeed rollcase, SCHURMAN Watermizer saw guide system, BENSHAW 300 hp soft start, 2006 upgrades include CONTROL LOGIC PLC system, (16) new guides, babbit mold, new arbor, sleeves, spacer, bearings, cab, controls, spare saws, parts, s/n: 2595

• SCHURMAN 4TA36 4"x36" splined top arbor board edger w/scanner, set up to run 2", RELIANCE 250 hp/1775 rpm arbor drive, 19" saws, 1999 USNR 625 16' edger maximizer scanner, 2006 GEO2 mill expert upgrade, Timber Grafix event viewer, recorder, 625 maximizer infeed system, infeed transfers, 1999 LUNDEN unscambler, board turners, reject tipple, scanner infeed hooks, pin stops, positioning pins, cushion cylinders, table & infeed press rolls, parking ramps, pickers, 1998 PFS 73 hp hydraulic unit, 225 gallon SCHURMAN Watermizer saw guide system, controls, electrics, spare saws, parts, s/n: 2530
• 1986 SCHURMAN 6TA36 6"x36" splined top arbor gang edger w/scanners, (2) TOSHIBA 200 hp/1770 rpm, 22" saws, dual DYNA-VISION M6-17-2 scanner heads controlling LAND EAST 2120 dual side lineal positioned skew rack carriage, infeed transfers, (7) knurled feed through rolls, (2) 9" powered top press rolls, ASPR control system, #3 splined arbor sleeve, SCHURMAN Watermizer saw guide system, 1999 SAS 115 hp/400 gallon hydraulic unit, spare saws, scanner heads, parts, s/n: 2529
• SCHURMAN 4TA24 4"x24" splined top arbor edger, WESTINGHOUSE 100 hp/1760 rpm, infeed rollcase, outfeed belt, spare saws, s/n: 1545

• CM&E 4243-44 vertical mount slabber chipper, setup to run 1", adjustable to 6", WESTINGHOUSE 100 hp, hold downs, in & outfeed rollcases

• AMI 8' over end stacker, dual lathe magazines, 3-arm hydraulic lumber hoists, (3) lumber placer arms, infeed belts to gravity rolls, outfeed transfer to rollcase, 50 hp hydraulic unit, spare parts

• 1994 AMI NG2 trimmer, 12' cut, 17' pass, fixed zero & 12' saw, (3) adjustable saws from 7'-12', individually motorized air drop 22" saws, 6" cut, hydraulic fence, infeed transfers w/even end rollcase, 2006 DIGITRON setworks package, 2001 PLC 200NC tong loader, controls, electrics, spare saws, parts, s/n: NC390-1ZP

• 1998 LUCIDYNE Color Scan 200 grade mark reader, s/n: 2241

• 1999 GJ CLAUSEN lumber printer w/(4) arms, double screw adjuster, floor mount & reversing mechanism, (2) hold downs, chain disengage, custom color option, heated ink roll

• 1997 planer hula saw system w/(2) 18" saws, 7-1/2 hp/3600 rpm, gravity rolls, belt, 1"-4" thick x 4"-8" wide x 4'-10' 2" long, s/n: 1673
• 1988 sawmill hula system w/(2) 18" saws, 7-1/2 hp/3600 rpm, gravity rolls, belt, 1"-4" thick x 4"-8" wide x 6'-12' 2" long, s/n: 1518

• WOODS 414M planer profiler w/(4)heads, 6"x15", (14) knives, 75 hp top head, 50 hp bottom head, 30 hp side heads, (4) hydraulic infeed rolls, (3) outfeed, hydraulic chip breaker, PFS 125 hp hydraulic unit w/(2) new pumps in 2006, spider, controls, spare heads, knives, parts, s/n: 31820

• COASTAL 15' dual hydraulic driven pineapple feed table w/(4) 10"x29", 10"x12" spiral roll, 10"x12" knurled roll, hydraulic speed-up roll

• SIGNODE M22-MP44 steel bander packaging line w/top & side squeeze, dual batten insert, end squeeze, 10, 60 hp hydraulic units, in & outfeed transfers, rollcases, 5/8" x .020 banding, s/n: Z-581

• 1988 MORRISON KNUDSEN 36X48-001-WH rotary knife hog, 200 hp, BENSHAW soft start, infeed belt conveyor, MDI CR85, s/n: 90760-12-84

• WSM 66" 8-knife chipper,WEG 300 hp/1190 rpm, horizontal infeed, bottom discharge, BENSHAW RBX-1-S-477A-17C motor brake, s/n: 0600253

• WSM 8'x10' 3-deck shaker screen w/rebuilt screen basket, upper & lower screens, discharge chutes, new hanger rod assemblies, neoprene oil boots

• 10' wide x 12' long x 7' high twin screw live bottom surge bin

• (3) PEERLESS 30-unit hydraulic shavings, chip, & sawdust bins
• (2) PEERLESS 14-unit hydraulic bark bins

• 2003 QNW V-250-B rotary screw compressor, 250 hp, air cooled, BALDOR adjustable speed inverter, 29895 hrs, s/n: 030192
• 1984 QNW 740B rotary screw compressor, 150 hp, air cooled, 67000 hrs, s/n: 840315
• PNEUMATECH PES2100 heat reactivated regenerative air dryer, 2100 scfm @ 150 psig, twin towers, ZEKS mist eliminator, s/n: 9405-S117383R-6117
• Approximately 6'x16' vertical, 4'x16' horizontal air receivers

• ARMSTRONG profiler facer
• ARMSTRONG #25 sharpener, s/n: 8805
• ARMSTRONG #3-60C stretcher roll, s/n: 11162
• ARMSTRONG #3-10 stretcher roll, s/n: 16507
• ARMSTRONG #16 sharpener, s/n: 11212
• NEWMAN G200 tub grinder, s/n: 200174
• IMW 380 auto dual side grinder
• IMW 240SS guide surface grinder
• JEFFREY JF200 travel bed profile grinder
• NIELSEN chain sharpener
• USNR true flow grinder
• SALEM babbitt grinder
• ARMSTRONG 8450C-60 tension gage grinder
• (2) ACME hand gummers
• Assortment of filing & grinding room equipment including: circle saw setup stand, anvils, guide grinder, granite blocks, guide, new knives, hoists, much more

• MCGRAW EDISON 2500 kva pad mounted transformer, 12470Y7200 high voltage, 480Y277 low voltage, installed September, 2006
• (3) sections WESTINGHOUSE 3000 amp mains
• (60+) sections ALLEN BRADLEY 2100 bulletin MCC's
• Transformers to 2500 kva
• Starters and disconnects to 300 hp
• BENSHAW 300 hp brake, (2) 200 hp brakes
• BENSHAW 300 and 200 hp soft starts
• ALLEN BRADLEY PLC's
• Electric spares including starters, disconnects, transformers, capacitors, heaters, relays, fuses, wire, conduit lot w/approximately 4300 connected

• WSM SCSB46 24"x42' vibratory conveyor, 5' fiberglass tub, fines drop, s/n: 329589, w/MDI CR85 metal detector, s/n: 71689, new pan, springs in 2006
• VIBRA PRO 18"x61', 18"x41'vibratory conveyors
• MILL POWER 18"x74', 18"x46' vibratory conveyors
• Large quantity of log decks, transfers, conveyors, rollcases
• (100+) SKK gearheads, motors, double reductions

• JET GH1860RX gear head engine lathe, 18"x60" swing, 3" spindle bore, 20-1600 spindle speed, 3 & 4 jaw chucks, tool post, tail stock, threading, steady rest, s/n: 26249706015
• BRIDGEPORT vertical milling machine, 80-2720 spindle speeds, 1 hp head, 9"x42" T-slot table, s/n: J-57866
• WELLSAW 613 horizontal metal cutting bandsaw
• Hydraulic shop press
• MILLER BOBCAT 225 CC/CV, AC/DC welder/8000 watt generator
• (5) MILLER SRH333, DIALARC 250 welders
• ABELL HOWE 2 ton jib arm crane w/HARRINGTON 2 ton electric chain hoist, pendant controls
• RIDGID 300 threader
• JET 16" 16-speed floor drill press, 3/4 hp, single phase
• (2) ROBBINS & MEYERS 10000 lb trailer loaders
• Portable oil transfer pump, hand banders, carts, fiberglass ladders, GRACO paint pumps, safety rigging, HUSQVARNA 575XP, STIHL MS310 gas chain saws; fluorescent markers, (3) INTERMEX easy coder 3400 printer w/ribbons, glass front presentalion cases, SIMPLEX STARPORT time card system, personnel lockers, office furniture, spare cylinders, service kits, parts, oxy-acetylene carts, hose, gauges and torches; welding rod & supplies, lathe, machine shop tooling, WATERLOO magnum 10-drawer bench, top tool chest, shafting, double end grinders, benches, tables, wood lockers, hydraulic motors, pumps, hoses, couplers, broach set, fans, lights, catwalks, hand & power tools, belt lacing, steel stock, fire extinguishers, vises, sprockets, couplers, hubs, bearings/anvil, racking, chain repair parts, lighting supplies, pipe fittings, cable belts, new chain & belting, filters, air bags, valve bodies, spare electrical, motors to 200 hp, gearheads, reducers, pulleys, wire, pipe stand, conduit, air hose, battery charger, (3) floor jacks, flammables cabinets, oil & grease pumps, CAT parts, parts bins, spare parts for debarker, chop saws, headrig, carriage, log turner, resaw, scragg, edgers, scanners, stacker, trimmer, hula saws, planer, bander, log sorter, chipper, chip screen, surge, chip bins, compressors; large quantity of electrical stores, 4" pipe threader, welders, large quantity of Temposonic wands & cylinders; (20+) hydraulic motors & pumps, much more!

• Approximately 25,000 sq ft all steel irregular shaped sawmill building with CBC and PBS additions from 1993 to 1997
• Approximately 10,000 sq ft wood framed/steel & wood clad shop buildings
• Approximately 2,600 sq ft all steel clear span bander building
• Approximately 1,300 sq ft all wood lunchroom

• 2000 CAT 330B-LL heel boom log loader, PIERCE TC60 swivel grapple, 43' heel boom, 3306 turbo, replaced undercarriage, resealed boom cylinders, replaced rotex seals & grapple cylinder, 20,650 hrs, s/n: 6DR3597
• 1979 CAT 235SPL track mounted PIERCE swivel grapple heel boom log loader, 3306 turbo, triple grouser tracks, 13,369 hrs, s/n: 32K2386
• 1973 LETOURNEAU 2594 log stacker, CUMMINS 400BC3 turbo diesel, 4 wheel drive, 33.25-35 tires, 2327 hrs, s/n: 1112
• 1979 CAT 980C rubber tire log loader, new engine installed 7/04, MEDFORD log forks, 29.5x25 tires, 16,700 hrs, s/n: 63X0117
• 1994 JOHN DEERE 624G rubber tire loader, 6068T diesel, new transmission, top clamp log forks, TOYO asphalt tires, 16,298 hrs, s/n: D547121
• (2) 1976 CAT 966C rubber tire log loaders, CAT 3306 diesel, top clamp forks, 23.5-25 tires, enclosed cabs, s/n's: 76J2738, 76J0759
• 1985 CAT 936 rubber tire loader, CAT 3304 diesel, top clamp forks, 20.5R25 tires, enclosed cab, 42,768 hrs, s/n: 33Z01391
• 1973 CAT 920 rubber tire log loader, CAT 3304 diesel, bucket, 15.5-25 tires, enclosed cab, 4,261 hrs, s/n: 75J2058
• 1991, 1989 HYSTER H90XLS 9000 lb pneumatic forklifts, propane, 145" 2-stage mast, side shift, 42" forks, s/n's: F005D03936L, F005D01972K
• 1995, 1987 HYSTER H80XLS2 8000 lb pneumatic forklifts, propane, 145" 2-stage mast, side shift, 42" forks, s/n's: G005D054435, F005D01735K
• HYSTER H60C 6000 lb pneumatic forklift, propane, approximately 145" 2-stage mast, side shift, 42" forks, s/n: C5D-3672-H
• CAT V40B 4000 lb pneumatic forklift, propane, 156" 2-stage mast, side shift, 42" forks, s/n: 79M805
• 1994 CASE Uniloader 1840 skidsteer loader, CASE 4-390 diesel engine, hydrostatic transmission, bucket, 145" max lift, 6,500 hrs, s/n: J4F0132412
• 1997 KENWORTH W900A tandem axle 2000 gallon water truck, NTC350BC diesel, EATON FULLER 8 speed transmission, front and back spray bars, 2" hose reel, PTO pump
• 1999 CHEVY 2500 4x4 pickup, V8 , auto, tool box
• 1998 FORD RANGER XLT extended cab pickup, 4 cyl, manual
• 1996 FORD RANGER XLT extended cab pickup, 4 cyl, manual
• 1990 FORD F250 4x4 8' steel flatbed, V8, auto, w/LINCOLN welder, compressor, lube pump, tool boxes

• 10% BUYERS PREMIUM
• PAYMENT: Full payment must be made by no later than 4pm, Wednesday, August 22.
• A 25% deposit is required by the close of business auction day.
• Cash, cashiers check, Master & Visa Cards, wire transfers only. Personal or company checks accepted ONLY with bank letter of guarantee.
• Absentee bids accepted with 25% deposit
• REMOVAL: No purchase may be removed during the auction unless otherwise announced by the auctioneer. Equipment removal schedule announced on auction day.
• Announcements made by the auctioneer at the time of sale take precedence over printed matter.
• Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
• Due to safety & insurance reasons, persons under 12 not admitted.


• Washington Auctioneers License #1960

• From northbound I-5 in Portland, take the I-405 exit (299B).
• Drive north on 405 approximately 2.5 miles to the US-30/St Helens exit (#3). Drive north on Hwy 30 approximately 27.9 miles to Deer Island Road in St Helens..
• Turn right on Deer Island Road. The auction site is ahead, on the right.


• From southbound I-5 in Portland, take the I-405 exit (302B).
• Drive south on 405 approximately 8/10 mile to the US-30/St Helens exit (#3).
• Drive north on Hwy 30 approximately 27.8 miles to Deer Island Road in St Helens.
• Turn right on Deer Island Road. The auction site is ahead, on the right.

FOOD SERVICE AVAILABLE AT THE AUCTION SITE