Advance Bid Auction X Catalog

• SALEM 50" 5-arm ring debarker w/66" bypass, GE 75 hp/1175 rpm ring drive motor, alligator chain infeed & outfeed, air hold down rolls, hourglass outfeed rolls, GE 60 hp gen set to DC motor w/reducer, 15 hp hydraulic unit, cab, controls & electrics
• L&M 8' chain type cut-off saw, LINCOLN 20 hp motor, cradle & cylinder
• KLAMATH 60" 3-knee carriage, airdogs, & flippers, rack & pinion positioning, 5 trucks, pantograph, rails, bumpers, FARWEST electrics, LLOYD controls, booth, s/n: 544
• WESTINGHOUSE 200 hp DC carriage drive w/WESTINGHOUSE 540kw @ 1000-1300rpm DC generator to FAIRBANKS 200 hp/900 rpm motor, spool & cable, blower w/motor
• SIMCO RAMIC log scanning system w/diameter scanner, length scanner, (19) eyes & relays, scans 5'-50' length, 47-1/2" diameter
• CM&E slabber w/200 hp motor, ES/IE setworks, 15 hp hydraulic unit
• KLAMATH 7' headrig, GE 300 hp/600 rpm drive motor, 1" spoked-top wheel, mechanical strain, slat bed feed thru w/drive motor, controls
• KLAMATH 7' resaw, 200 hp/700 rpm drive motor, dual hydraulic driven infeeds w/setworks, s/n: 1004
• SCHURMAN 6TA48 edger w/top keyed arbor, 125 hp arbor drive motor, PORTLAND IRON WORKS 4-shifting saw setworks, SCHURMAN oil mist system, 12' infeed rollcase w/drive-motor, 16' outfeed rollcase w/edge picker, SKK drive motor, (4) laser lights, s/n: 1202
• PORTLAND IRON WORKS 4TA48 edger w/top keyed arbor, approximately 100 hp arbor drive motor, PORTLAND IRON WORKS 4-shifting saw setworks, 12' infeed rollcase w/drive motors, 16' outfeed rollcase w/edge pickers, SKK drive motor
• SUMNER trimmer, trim 16', pass 20', 40 hp drive motor, zero fence & saw, 40' pass thru lugged chain transfer w/even end chain & rolls, carryover wheels, 8-strand tipple, drive motors, controls & electrics
• LUNDEN 16' auto sticker stacker, w/2-strand auto placement sticker transfer, 5-strand infeed transfer, lumber dealing arms, 2-arm package hoist, hydraulic support unit, infeed tipple
• 16 bin edge sorter, 220' 2-strand 81x transfer w/SKK drive motor, (8) 18' 4-strand 81x transfers w/SKK-5 hp/20 rpm drive motors, (8) 22' 4-strand 81x transfers w/SKK 5 hp/20 rpm drive motors, TOSHIBA 5 hp starters, controls & electrics
• 16' 4-arm mechanical breakdown hoist w/GE 15 hp motor w/brake to reducer
• WSM 4032B hammer hog w/300 hp/1170 rpm drive motor, s/n: 43984
• SUMNER 66" 8-knife chipper, drop feed, bottom discharge, 200 hp/570 rpm drive motor, s/n: 2563
• RADER 25" x 30" high pressure blower w/60 hp drive motor, controls & silencer
• 16" x 26" high pressure blower w/(2) silencers
• AMF 60" blower w/60 hp drive motor
• RADER 25" x 30" feeder w/TOSHIBA 5 hp motor to FALK reducer
• High & low pressure blowpipe, diverters & hardbacks
• MILLPOWER CS 36120 3'x 10' vibratory conveyor w/drive motor, s/n: 83077
• ROTEX 6'x 12' 3-deck chip screen w/drive motor
• 12' disc scalping rollcase w/SKK drive motor
• Approximately 10' x 12' x 16' surge bin w/auger bottom, drive motor to shaft mounted reducer
• ROYAL 24-unit hydraulic chip bin
• PEERLESS 20-unit air operated chip bin w/(3) auger bottom, drive motor to shaft mounted reducer
• Shop built 8000 lb trailer loader w/motor, winch & electrics

• ARMSTRONG #6 sharpener, s/n: 8213, w/DUSTKOP collector
• ARMSTRONG #4 sharpener w/DUSTKOP collector
• ARMSTRONG #5 stretcher roll, s/n: 7965, w/clamp, anvils & bench
• ARMSTRONG 3-10 stretcher roll, s/n: 8153
• ARMSTRONG #25 sharpener, s/n: 3744 w/DUSTKOP collector
• (2) ARMSTRONG #16 sharpeners, s/n's: 3916, 8771, (1) w/DUSTKOP collector
• ACME sharpener
• HOE guide grinder
• NIELSEN chain sharpener
• CM&E #41 bent knife grinder
• COVEL HANCHETT CK36 travel bed grinder
• BARNHARDT grinder
• ARMSTRONG pneumatic swages
• Shapers
• COVEL band saw shear
• large quantity of grinding wheels, edger saws, bandsaw blades
• (3) BEEBE BROS cable winches
• (2) hydraulic powered cable winches

• GE 2-Section 2500 amp AV line switchboardTRUMBULL 1-section 1600 amp main mill disconnect
• GE 4000 amp/600 volt air circuit breakerGE 5-section MCC w/(11) switches
• YASAWA 175 kw combo starter
• GE size 5 combo starter
• (2) GE size 4 combo starters
• (2) GE size 3 combo starters
• SAFTRONICS SY6 solid state converter
• ALLEN BRADLEY SMC 2 controller
• SQUARE D 600 amp safety switch
• WESTINGHOUSE 600 amp safety switch
• SQUARE D 400 amp safety switch
• BULLDOG 200 amp safety switch
• GE 300 line electrics
• GE 200 line electrics
• transformers
• capacitors
• HID & fluorescent lighting
• fixtures,conduit, & conduit fittings
• monitors
• starters
• breakers
• conduit & wire throughout plant site

• 1964 GENERAL ELECTRIC 2.5 megawatt turbine, (13) stages @ 225 lbs, 600 TTF operating pressure, 60,000 lb/hr throttle flow, 2" HEA-ABS condensing pressure, 13.5 lb/kw water rate @ full load, 15 psi, automatic extraction port, s/n: 17598
• 1964 GENERAL ELECTRIC 3150 kva generator, 2300 volt, 752 stator amps, 125 volts excitation, direct shaft driven, water cooled, .08 power factor, (58,000 cumulative hours on line)
• POWELL 2400 volt high resistance ground-gardGE 8000 line 4 section MCC w/18 switches
• SQUARE D main distribution panels
• WELLONS Controls
• ECOLAIRE 2-pass water type condenser w/28,500,000 btu/hr (4250 GPM) cooling capacity
• 1973 NEBRASKA 40,000 lb/hr @ 225 lbs wood fired fuel boiler, 5,574 sq ft heating surface, 526 sq ft water walls, controls & electrics, s/n: 13310, NB #2711
• WELLONS fly ash recovery system consisting of PACE 36" blower w/drive motor, WELLONS furnace, collection cone w/feeder, outfeed auger, drive motor, collection stack, PACE 49" blower w/drive motor, emissions stack
• BAC PRITCHARD 4338-2 mechanical draft cooling towers , (2) 10' diameter fans w/(2) 40 hp drive motors, s/n: 68842
• WELLONS A-30-35 Posi-flow silo w/160 unit capacity twin auger distribution, drive motors, s/n: 1373B
• ALL STEEL Co-Gen building, 40' wide x 75' long x 35' eaves, w/10' roll up-door & man doors
• 36' x 10 ton underslung bridge crane w/power travel, pendant controls

• 1990, 1987 CAT SR4 standby generators, 1250 kw standby power, 1136 kw prime power, CAT 3512 twin turbo diesel engines, radiator, silencer, 24 volt batteries, s/n's: 6PAO1291, 6PAO0841, ASCO/DELTA controls, matching panels in Co-Gen plant, 480 volt - 2000 amps, s/n's; 12109-01 (7,400 hrs), 11519-01 (9766 hrs)
• 1000 gallon diesel fuel tank

• INDEK 12,075 lb/hr @ 350 lbs, gas fired package boiler, 350 hp, 1758 sq ft heating surface, 14,465 mbh rated input, 11,716 mbh rated output, 133,112 btu/cu ft heat release, 110.02 cu ft furnace capacity, s/n: 11298
• HB SMITH Series 2BA-14 oil or gas fired package boiler, 15 lbs steam, 50 psi water, 11,525 sq ft of steam, 2,766,000 btu/hr steam, 3,098,000 btu/hr water, 31.5 gph light oil, 4517 mbh gas, 3563 lb/hr min relief, s/n: N93-475
• Approximately 5000 gal fuel tank

• (2) MOORE OREGON 33' x 105' double track steam-fired kilns, zonal controlled, 75 hp line shaft-driven fans, MOORE OREGON controls, GE & WESTINGHOUSE electrics, 10' x 70' kiln control house
• (3) Concrete block kilns w/(6) 18' aluminum doors, aluminum skin roof, blowers, piping & valves, FRYER dry kiln controls, electrics
• (100) kiln carts, I-beam construction, 54" x 114" overall, 30" cc x 72"
• (115,000+) - 1"x 1-3/4" x 52" stickers in metal racks & bundles

• Huge assortment of H78 & 81X transfers w/drives, H110 & H112 conveyors, cleanouts w/drives, rollcases w/drives

• LEHMAN 20" x 100" engine lathe, 3 jaw chuck, tool post, tail stock, threading, w/lathe tooling
• CINCINNATI BICKFORD 4' radial arm drill w/T-slotted knee
• MILWAUKEE #2 vertical mill w/T-slotted table
• POWERMATIC 15" drill press
• Large assortment of shop equipment & tools including: grinders, laser lights, 40, 20 hp hydraulic units, conduit, pipe, filters, welders, DC generator set, motors to 400 hp, lights, cylinders, rolls, chain, bearings, sprockets, shafting, RADER 12" x 36" high pressure blower, bandmill wheels, ZURN 55A air dryer, SMITHWAY XL ripper, 7.5 & 5 hp tank mounted compressors, fuses, thermal units, wire, heaters, starters, monitors, hand carts, disconnects, bearings, seals, gaskets, fasteners, hardware, 20,000 gal diesel tank, chain hoists, grease pumps & much, much more!

• ALL STEEL mill building, approximately 150' wide x 180' long x 20' eaves(irregular shaped)
• ALL STEEL shop building, 50' wide x 60' long x 20' eaves
• ALL STEEL electrical shop building, 22' wide x 26' long x 10' eaves

• NORTHWEST track mounted shovel/log loader, MURPHY MP20 diesel engine, 32" tracks, spare log grapples, clam shell, s/n: 24359

• 5% BUYERS PREMIUM
• PAYMENT: Full payment must be made by no later than 4 pm, Wednesday, April 5.
• A 25% deposit is required by the close of business, auction day. Cash, cashiers check, Master & Visa Cards only. Personal or Company checks accepted ONLY with bank letter of guarantee.
• Absentee bids accepted with 25% deposit
• REMOVAL: No purchase may be removed during the auction. small purchases must be removed 1 hour after the sale or between 8 am & 4:30 pm Wednesday & Thursday, April 5 & 6. Large equipment removal schedule to be announced on auction day.
• Announcements made by the auctioneer at the time of sale take precedence over printed matter.
• Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
• Washington Auctioneers License #48

• From Hwy 36 in Susanville, drive east on E Riverside one block, road turns into Johnstonville Road then drive approximately 7/10 miles to auction site, located on the on right

HIGH COUNTRY INN	530-257-3450
BEST WESTERN TRAILSIDE INN	530-257-4123
SUPER 8	530-257-2782

• Reno, NV airport is served by most major airlines and rental car companies