|
LOT# |
QTY. |
DESCRIPTION |
| 1 | 1 | OSTER 2" CAP. HAND THREADER |
| 3 | 2 | G.E. 30 AMP DISCONNECT SWITCHES |
| 4 | 2 | G.E. 30 AMP DISCONNECT SWITCHES |
| 5 | 1 | LOT, MONITORS |
| 6 | 1 | KRONOS LOT, TIME CLOCKS |
| 7 | 2 | 6" 6-KNIFE MOULDER HEADS |
| 8 | 2 | 6" 6-KNIFE MOULDER HEADS |
| 9 | 6 | 4" 6-KNIFE MOULDER HEADS |
| 10 | 2 | 2-7/8" 6-KNIFE MOULDER HEADS |
| 11 | 1 | LOG TONG |
| 12 | 1 | LOG TONG |
| 13 | 1 | LOG TONG |
| 14 | 1 | U.S. 3 HP/1750 RPM MOTOR |
| 15 | 1 | LOT, ASSORTED BEARINGS |
| 16 | 1 | LOT, (2) 18" CARBIDE TIP CIRCULAR SAW BLADES W/1" ARBOR HOLE |
| 17 | 1 | LOT, OPCON EYES |
| 18 | 1 | LOT, RAILROAD CHALK |
| 19 | 1 | ABC FIRE EXTINGUISHER |
| 20 | 1 | ABC FIRE EXTINGUISHER |
| 21 | 1 | ABC FIRE EXTINGUISHER |
| 22 | 1 | LOT, H78 ROOFTOP CHAIN |
| 23 | 1 | METAL DESK |
| 24 | 1 | METAL DESK |
| 25 | 1 | METAL DESK |
| 26 | 1 | LOT, ADJUSTABLE PALLET SHELVING W/3 UPRIGHTS |
| 30 | 1 | QUINCY QNW 950C 250 HP ROTARY SCREW AIR COMPRESSOR 740353 |
| 31 | 1 | CUTLER HAMMER SIZE 6 STARTER W/600 AMP ADJUSTABLE TRIP BREAKER |
| 32 | 1 | QUINCY QNW 850A 200 HP ROTARY SCREW AIR COMPRESSOR W/ELECTRICS 72492 |
| 33 | 1 | AIR COMPRESSOR CONDENSER |
| 34 | 1 | AIR COMPRESSOR CONDENSER |
| 35 | 1 | 40' 4-STRAND H132 CHAIN LOG DECK W/H&T SPROCKETS, S-DRIVE, & STEEL RACES |
| 36 | 1 | RELIANCE 15/7-1/2 HP, 1730/865 RPM MOTOR W/FALK 20 RPM REDUCER, & DRIVE CHAIN (LOT 35 DRIVE) |
| 37 | 1 | 72' TWIN-STRAND H132 CHAIN LOG HAUL CONVEYOR W/H&T SPROCKETS, S-DRIVE, & STEEL TROUGH |
| 38 | 1 | G.E. 25 HP MOTOR W/FALK 30 RPM REDUCER, & DRIVE CHAIN (LOT 37 DRIVE) |
| 39 | 1 | SALEM 60" 5-ARM RING DEBARKER W/DC RING DDRIVE MOTOR, DC TO FALK REDUCER IN & OUTFEED CHAIN DRIVE MOTOR, PNEU. HOLD DOWN ROLL, LOG CENTERING ARMS, & MANZELL LUBE SYSTEM (D.C ELECTRICS SOLD AT LOTS 61 & 62) |
| 40 | 1 | DEBARKER/DECK SAW LINE CONTROL BOOTH W/ALL CONTROLS |
| 41 | 1 | L&M BAR CHAIN LOG CUTOFF SAW W/15 HP DRIVE MOTOR, & LOG SUPPORT ARM W/CYLINDER |
| 42 | 1 | 8' HOURGLASS ROLLCASE W/(3) 38" ROLLS |
| 43 | 1 | 22' TWIN-STRAND H124 CHAIN LOG HAUL CONVEYOR W/H&T SPROCKETS, STEEL TROUGH, & 3-ARM LOG KICKER W/CYCLINDER |
| 44 | 1 | G.E. 3 HP/68 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 43 DRIVE) |
| 45 | 1 | 16' 4-STRAND H78 CHAIN LOG DECK W/H-SHAFT, T-SPOOLS, STEEL RACES, & PLATE |
| 46 | 1 | 20' 4-STRAND H124 CHAIN LOG DECK W/H&T SPROCKETS, S-DRIVE, STEEL RACES, & PLATE |
| 47 | 1 | SKK 5 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 45 DRIVE) |
| 48 | 1 | SKK 10 HP/30 RPM DOUBLE REDUCTION GEARHEAD MOTOR W/DRIVE CHAIN (LOT 46 DRIVE, PLEASE PREVIEW) |
| 49 | 1 | 20' H78 CHAIN WASTE CONVEYOR W/H&T SPROCKETS, & STEEL TROUGH |
| 50 | 1 | HITACHI 2 HP/60 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 49 DRIVE) |
| 51 | 1 | 44' H78 CHAIN SAWDUST CONVEYOR W/H&T SPROCKETS, FLITES, & STEEL TROUGH |
| 52 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 51 DRIVE) |
| 53 | 1 | APPROX. 50' 3/4" LINK CHAIN BARK CONVEYOR W/22" FLITES, H&T SPROCKETS, & STEEL TROUGH |
| 54 | 1 | SKK 5 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 53 DRIVE) |
| 55 | 1 | 35' H78 CHAIN WASTE CONVEYOR W/H&T SPROCKETS & STEEL TROUGH |
| 56 | 1 | 2 HP MOTOR W/FALK 100 RPM REDUCER W/DRIVE CHAIN (LOT 55 DRIVE) |
| 57 | 1 | APPROX. 55' H78 CHAIN SAWDUST CONVEYOR W/H&T SPROCKETS, & STEEL TROUGH |
| 58 | 1 | G.E. 3 HP/68 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 57 DRIVE ON ROOF) |
| 59 | 1 | OVERHEAD CAMERA W/WEATHER ENCLOSURE |
| 60 | 1 | TROLLY W/RAIL |
| 61 | 1 | IES 100-HP DC SCR DRIVE MOTOR CONTROLLER W/118 KVA TRANSFORMER (DOWNSTAIRS) |
| 62 | 1 | IES 75-HP DC SCR DRIVE MOTOR CONTROLLER W/112.5 KVA TRANSFORMER |
| 63 | 1 | KEL-AIR D16A 1000 SCFM AT 100 PSIG REFRIGERANT COMPRESSED AIR DRYER (LOCATED OVERHEAD) 980533 |
| 64 | 1 | 8'X3' HORIZONTAL AIR RECEIVER TANK |
| 65 | 1 | FUSE DISCONNECT SWITCH (NO DATA AVAILABLE) |
| 66 | 1 | 40 HP HYDRAULIC SUPPORT UNIT |
| 67 | 1 | LOT, ASSORTED MOTORS & STATORS |
| 68A | 1 | LOT, SPROCKETS, CHAIN, & MISC. PARTS ON TOP TWO SHELVES |
| 68B | 1 | STEEL FRAMED SHELF |
| 69 | 1 | LOT, ASSORTED ELECTRICAL BOXES, WIRE, ELECTRICAL INVENTORY, & WOOD LADDER (PLEASE PREVIEW) |
| 70 | 1 | PNEUMATIC LUBE UNIT W/HAND TRUCK |
| 71 | 1 | LOT, HYDRAULIC MOTORS & PUMPS |
| 72 | 1 | LOT, ASSORTED BEARINGS ON THESE 2 SHELVES |
| 73 | 1 | LOT, ASSORTED MILL PARTS ON THIS ONE SHELF |
| 74 | 1 | LOT, ASSORTED CYLINDERS ON THIS ONE SHELF & FLOOR SECTION |
| 75 | 1 | LOT, ASSORTED PNEUMATIC & HYDRAULIC SYSTEM PARTS |
| 76 | 1 | LOT, CHAIN SAW BARS & PARTS |
| 77 | 1 | LOT, CYLINDER REPAIR PARTS W/CABINET |
| 78 | 1 | ALLEN BRADLEY 1770KCB TEST TERMINAL |
| 79 | 1 | LOT, EMPLOYEE WALL LOCKERS W/CONTENTS & METAL FOLDING CHAIRS |
| 80 | 1 | LOT, ASSORTED MILL PARTS & SUPPLIES W/REMAINING UNSOLD LOOSE CONTENTS OF ROOM |
| 81 | 1 | LOT, LOOSE CONTENTS OF OFFICE (AIR CONDITIONER NOT INCLUDED) |
| 82 | 1 | IES 200 HP SOLID STATE STARTER |
| 83 | 1 | LOT, ASSORTED MILL PARTS & SUPPLIES (LOOSE CONTENTS OF ROOM) |
| 84 | 1 | HOBART 300 AMP DC ARC WELDER |
| 87 | 1 | G.E. 25 KVA, 480 TO 240/120 KVA TRANSFORMER W/BREAKER PANEL |
| 88 | 1 | KLAMATH IRON WORKS 54RHTO-H 16'X54" 3-KNEE 5-TRUCK LINEAR POSITIONING LOG CARRIAGE W/INOVEC 386 LOG SCANNING SETWORKS - INCLUDES TOP & BOTTOM SCANNER BAR, MARKED ELECTRICS IN CONTROL BOOTH & INOVEC ROOM, RAIL, BUMPERS, & PANTOGRAPH. - HYDRAULIC SUPPORT UNIT SOLD AT LOT 241, SPARE PARTS SOLD AT LOT 322, DRIVE SOLD AT LOT 302 |
| 89 | 1 | HYDRAULIC LOG TURNER & FLIPPER ASSEMBLY (NO SCANNER EYES) |
| 90 | 1 | 11' 4-ARM LOG STOP & LOADER W/CYLINDER |
| 91 | 1 | CME 64 8-KNIFE LINEAR POSITIONING PRE-SLABBER W/200 HP DRIVE MOTOR. (SPARE PARTS SOLD AT LOT 312) |
| 92 | 1 | KLAMATH IRON WORKS 7' RIGHT HAND, MECHANICAL STRAIN SINGLE-CUT HEAD RIG VERTICAL BAND MILL W/SLAT CHAIN LANDING TABLE, SKK SLAT CHAIN DRIVE, & MOTOR DRIVE BELTS. (DRIVE SOLD AT LOT 243, SPARE PARTS SOLD AT LOT 361) |
| 93 | 1 | STEEL HEAD RIG CONTROL BOOTH W/CHAIR, & 18-MARKED PUSH BUTTON STATION ONLY |
| 94 | 1 | MY-TE 1000 LB CAPACITY SAW BLADE WINCH |
| 95 | 1 | ALLEN BRADLEY MINI PLC 2/16 CABINET |
| 96 | 1 | STEEL INOVEC ROOM W/(2) AIR CONDITIONERS, SPACE-GARD AIR CLEANER, & FIRE PROTECTION SYSTEM |
| 97 | 1 | LOT, WOOD DESK & DRESSER |
| 98 | 1 | 45' CHAIN DRIVEN HEAD RIG OUTFEED ROLLCASE W/(15) 48"X12-1/2" DIA. ROLLS, 16' LUMBER ON-BEARING ROLL, & STOP GATE W/CYLINDER |
| 99 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR (LOT 98 ROLLCASE DRIVE) |
| 100 | 1 | SKK 2 HP/59 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 98 ON-BEARING ROLL DRIVE) |
| 101 | 1 | 1989 KOCKUMS CANCAR 6' HORIZONTAL LINEAR POSITIONING BAND RESAW W/200 HP DRIVE MOTOR, HYDRAULIC STRAIN, 8-KNURLED ROLL FEED THRU ROLLCASE, & SPRAY MIST SYSTEM DIGITRON SETWORK IN CONTROL BOOTH 8933 (HYDRAULIC SUPPORT UNIT SOLD AT LOT 239 & 240) |
| 102 | 1 | 3-SIDED RESAW CONTROL BOOTH W/ALL CONTENTS EXCEPT DIGITRON SETWORK BOX |
| 103 | 1 | 17' CHAIN DRIVEN RESAW INFEED ROLLCASE W/(5) 30"X8-1/2" DIA. ROLLS, 4-STRAND JUMP ROLLER CHAINS (W/BOTH SHAFTS), & BOARD POSITIONING ARMS W/CYLINDERS |
| 104 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR (LOT 103 ROLLER CHAIN DRIVE) |
| 105 | 1 | LOT, TRANSFERS TO RESAW INFEED FROM HEAD RIG SIDE W/9' 5-STRAND H78 ROOFTOP CHAIN TRANSFER (W/H-SHAFT), JUMP TAIL SPROCKETS, 8' 5-STRAND H78 CHAIN TRANSFER (W/H&T SHAFTS), & UHMW LINED STEEL RACES |
| 106 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 105 ROOFTOP DRIVE) |
| 107 | 1 | G.E. 3 HP/29 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 105 H78 DRIVE) |
| 108 | 1 | LOT, TRANSFERS TO RESAW INFEED FROM MERRY-GO-ROUND SIDE W/11' 5-STRAND H78 CHAIN TRANSFER (W/H-SHAFT), T-SPROCKETS, 6' 4-STRAND ROLLER CHAIN ROLLCASE UNLOADING TRANSFER (W/H-SHAFT), JUMP TAIL SPROCKETS, & UHMW LINED STEEL RACES |
| 109 | 1 | HITACHI 3 HP/60 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 108 H78 DRIVE) |
| 110 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 108 ROLLER CHAIN DRIVE) |
| 111 | 1 | 19' CHAIN DRIVEN MERRY-GO- ROUND ROLLCASE W/(5) 48"X8-1/2" DIA. ROLLS |
| 112 | 1 | LOT, (9) MARKED ELECTRIC BOXES (LOCATED BEHIND LOT 111 ROLLCASE - PLEASE PREVIEW) |
| 113 | 1 | SAFETY MIRROR (LOCATED BY FILING ROOM WALL) |
| 114 | 1 | WARNING LIGHT |
| 115 | 1 | LOT, EXPANDED METAL CATWALKS & STAIRWAYS INSIDE SAWMILL BUILDING |
| 116 | 1 | 15' CHAIN DRIVEN RESAW OUTFEED ROLLCASE W/(4) 30'X8-1/2" DIA. ROLLS, & 4-STRAND ROLLER CHAIN ROLLCASE UNLOADING TRANSFER |
| 117 | 1 | SKK 5 HP/155 RPM GEARHEAD MOTOR (LOT 116 ROLLCASE DRIVE) |
| 118 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 116 ROLLER CHAIN DRIVE) |
| 119 | 1 | HYDRAULIC TIPPLE W/CYLINDERS |
| 120 | 1 | 13' 4-STRAND H78 MERRY-GO- ROUND CHAIN TRANSFER W/H&T SHAFTS, STEEL RACES & EXPANDED METAL DECK |
| 121 | 1 | SKK 2 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 120 DRIVE) |
| 122 | 1 | 23' CHAIN DRIVEN MERRY-GO- ROUND ROLLCASE W/(7) 62"X8-1/2" DIA. ROLLS, (1) 4-1/2" DIA. ROLLS, & (2) LUMBER STOP GATES W/CYLINDERS |
| 123 | 1 | HITACHI 5 HP/155 RPM GEARHEAD MOTOR (LOT 122 DRIVE) |
| 124 | 1 | CM VALVESTAR 1-TON CAP. ELECTRIC CHAIN HOIST W/TROLLY & RAIL; 3-PH |
| 125 | 1 | 15' 7-STRAND SPIKED H78 CHAIN TRASH DECK W/H-SHAFT, OREGON TAIL BENDS, & STEEL PLATE |
| 126 | 1 | 17' 5-STRAND H78 CHAIN TRANSFER W/H-SHAFT, T-SPROCKETS, LATTICE FRAMED STEEL RACES, & RETURNS |
| 127 | 1 | 14' 5-STRAND H78 CHAIN TRANSFER W/H-SHAFT, T-SPROCKETS, & STEEL RACES |
| 128 | 1 | HITACHI 5 HP/60 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 126 DRIVE) |
| 129 | 1 | G.E. 3 HP/66 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 127 DRIVE) |
| 130 | 1 | LOT, INFEED TO EDGER TRANSFERS W/9' 8-STRAND H78 ROOFTOP CHAIN TRANSFER (W/H-SHAFT), JUMP TAIL SPROCKETS, 6-1/2' 8-STRAND INCLINED H78 CHAIN TRANSFER (W/LUMBER STOP ARMS & CYLINDER), & STEEL RACES (NO HEAD SHAFT ON H78 TRANSFER) |
| 131 | 1 | SKK 2 HP/NO RPM DATA GEARHEAD MOTOR W/DRIVE CHAIN (LOT 130 H78 DRIVE) |
| 132 | 1 | G.E. 3 HP/66 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 130 ROOFTOP DRIVE) |
| 133 | 32 | SCHURMAN 85BA54 8"X54" COMBINATION EDGER W/GANG SITE, 3-LINEAR POSITIONING SAW SIDE, 350 HP ARBOR DRIVE MOTOR, (2) 30 HP FEED ROLL DRIVE MOTORS, SAWMIST SYSTEM, SWING AWAY OPENING, CONTROL CHAIR (W/CONTROLS), ALLEN BRADLEY MINI-PLC 2/05, & SPARE DRIVE BELTS (HYDRAULIC SUPPORT UNIT SOLD AT LOT 231) 2493 |
| 134 | 1 | 16' EDGER FEED TABLE W/5-ROLL KNURLED ROLLCASE (W/HYDRAULIC DRIVE MOTOR), 9' 8-STRAND 81X CHAIN INFEED TRANSFER (W/HYDRAULIC DRIVE MOTOR), LUMBER STOP ARMS, & LUMBER POSITIONING ARM (W/CYLINDERS) (PLEASE PREVIEW) |
| 135 | 1 | LOT, (3) LAHARCO LASER LIGHTS & (4) OPCON EYES ABOVE EDGER INFEED |
| 136 | 1 | 12-1/2' EDGER OUTFEED W/(7) 66"X6-1/2" DIA. ROLLS |
| 137 | 1 | 10' 7-STRAND 81X CHAIN TRANSFER (W/H-SHAFT), JUMP TAIL SPROCKETS (W/CYLINDERS), UHMW LINED STEEL RACES & & RETURNS |
| 138 | 1 | SKK 3 HP/68 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 137 DRIVE) |
| 139 | 1 | MILWAUKEE 1-TON CAP. 3-PH ELECTRIC CHAIN HOIST W/TROLLY |
| 140 | 1 | 6-STRAND MULTI-LENGTH H78 CHAIN TRANSFER (H-SPROCKETS), OREGON TAIL BENDS, (2) S-DRIVE SHAFTS, & STEEL RACES |
| 141 | 1 | MITSUBISHI 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 140 DRIVE) |
| 142 | 1 | LOT, (4) FOOT CONTROLLERS |
| 143 | 1 | 22' 4-STRAND H78 ROOFTOP CHAIN TRANSFER (W/H-SHAFT), T-SPROCKETS, & UHMW LINED STEEL RACES |
| 144 | 1 | 14' CHAIN DRIVEN ROLLCASE W/(4) 60"X10-1/2" DIA. ROLLS |
| 145 | 1 | SKK 5 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 143 DRIVE) |
| 146 | 1 | SKK 3 HP/68 RPM GEARHEAD MOTOR (LOT 144 DRIVE) |
| 147 | 1 | LOT, (3) MARKED ELECTRIC BOXES IN AREA |
| 148 | 1 | OXY/ACET BOTTLE STAND |
| 149 | 1 | IRVINGTON MOORE 66 LEFT HAND 16' CUT, 20' PASS INDIVIDUALLY MOTORIZED BOARD TRIMMER W/LUGGED FEED THRU CHAIN TRANSFER (W/H&T SHAFTS), END EVENING ROLLCASE, MINUS FENCE, 8' 4-STRAND H78 INFEED TRANSFER, & ALLEN BRADLEY MINI-PLC 2/16 SETWORKS, (NO TAIL SHAFT ON H78 INFEED, NO TRANSFER DRIVE MOTORS) |
| 150 | 1 | SKK 2 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (TRIMMER INFEED DRIVE) |
| 151 | 1 | 20' 2-SECTION LUGGED 81X TRIMMER OUTFEED TRANSFER W/HEADSHAFT, CENTER SHAFT, & STEEL RACES (NO TAIL SHAFT) |
| 152 | 1 | LOT, (9) 112"X8-1/2" DIA. END EVENING ROLLS W/DRIVE CHAIN (NO FRAME) |
| 153 | 1 | HITACHII 10 HP/60 RPM GEARHEAD MOTOR W/DRIVE CHAIN (TRIMMER FEED THRU TRANSFER DRIVE) |
| 154 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR (LOT 152 DRIVE) |
| 155 | 1 | 22' 9-STRAND H78 GREEN CHAIN W/H-SHAFT, UHMW LINED STEEL RACES & RETURNS (NO TAIL SHAFT) |
| 156 | 1 | G.E. 3 HP/25.56:1 RATIO GEARHEAD MOTOR W/DRIVE CHAIN (LOT 155 DRIVE) |
| 157 | 1 | HYDRAULIC PEDESTAL LOG LOADER W/GRAPPLE, & 25 HP PUMP |
| 158 | 1 | LOT, 41' 4-STRAND H78 CHAIN TRANSFER W/H&T SPROCKETS, S-DRIVE, STEEL RACES, & 8' 4-STRAND JUMP ROLLER CHAIN TRANSFER (W/AIR BAGS) |
| 159 | 1 | SKK 7-1/2 HP/56 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 158 DRIVE) |
| 160 | 1 | APPROX. 30' H110 DRAG CHAIN TRIMMER CLEAN-OUT CONVEYOR W/H&T SPROCKETS & STEEL TROUGH |
| 161 | 1 | G.E. 3 HP/68 RPM GEARHEAD MOTOR W/DRIVE CHAIN, & DISCONNECT SWITCH (LOT 160 DRIVE) |
| 162 | 1 | APPROX. 38' H112 DRAG CHAIN WASTE CONVEYOR W/H&T SPROCKETS, STEEL TROUGH, & EXPANDED METAL BRIDGE |
| 163 | 1 | G.E. 3 HP/68 RPM GEARHEAD MOTOR W/DRIVE CHAIN & DISCONNECT SWITCH (LOT 162 DRIVE) |
| 164 | 1 | 33'X23" BELT CONVEYOR W/H&T DRUMS, & STEEL TROUGH |
| 165 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN, & DISCONNECT SWITCH (LOT 164 DRIVE) |
| 166 | 1 | 11' 7-STRAND H78 ROOFTOP CHAIN TRANSFER W/H&T SHAFTS, STEEL RACES, CATWALKS, & STEEL FRAME AT INFEED |
| 167 | 1 | HITACHI 3 HP/60 RPM GEARHEAD MOTOR W/DRIVE CHAIN, & ATTACHED ELECTRICS (LOT 166 DRIVE) |
| 168 | 1 | 123'X12" WASTE BELT CONVEYOR W/H&T DRUMS, STEEL TROUGH, & SLOPES |
| 169 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR, DRIVE CHAIN, & DISCONNECT SWITCH (LOT 168 DRIVE) |
| 170 | 1 | 17'X12" WASTE BELT CONVEYOR W/H&T DRUMS, & STEEL TROUGH |
| 171 | 1 | SKK 1 HP/100 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 170 DRIVE) |
| 172 | 1 | 16' 6-STRAND H78 ROOFTOP CHAIN TRANSFER ON BREWCO LINE INFEED W/H-SHAFT, OREGON TAIL BENDS, STEEL RACES, & RETURNS |
| 173 | 1 | 77" HIGH X 15' WIDE 6-STRAND 81XH CHAIN LUMBER SINGULATOR W/H-SHAFT, OREGON TAIL BENDS, STEEL RACES & PLATE |
| 174 | 1 | 61/2' 5-STRAND C55D CHAIN LUMBER LANDING TABLE W/H-SHAFT, OREGON TAIL BENDS, STEEL RACES & PLATE, & GRAVITY ROLLCASE |
| 175 | 1 | SKK 2 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 174 DRIVE) |
| 176 | 1 | BREWCO BSBH8 SUPER-BAND 28" HORIZONTAL BAND RESAW W/20 HP 3-PH BANDMILL DRIVE MOTOR, PNEUMATIC SHIFTING SAW, FEED THRU BELT CONVEYOR (W/HYDRAULIC DRIVE MOTOR), HYDRAULIC PRESS FEED ROLLS, & HYDDRAULIC SUPPORT UNIT B1A4138 |
| 177 | 1 | 11' X 12" SAW CLEANOUT BELT CONVEYOR W/H&T DRUMS, STEEL TROUGH, & SLOPES |
| 178 | 1 | SKK 1 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 177 DRIVE) |
| 179 | 1 | 31'X12" MERRY-GO-ROUND BELT CONVEYOR W/H&T DRUMS, STEEL TROUGH, LUMBER STOP GATE, & ATTACHED STAIRWAY |
| 180 | 1 | PUSH BUTTON CONTROL PANEL W/(3) FOOT CONTROLLERS |
| 181 | 1 | LOT, (2) FIXED POSITIONED PNEU. LIFT 18" CIRCULAR SAW W/(2) ARBOR MOTORS, & VERTICAL STEEL SUPPORTS TO OVERHEAD HORIZONTAL BEAM |
| 182 | 1 | 18' 5-STRAND C55D CHAIN TRANSFER W/H-SHAFT, OREGON TAIL BENDS, STEEL RACES & RETURNS, OFFBEARING ROLLS, & STEEL BUNK AT END OF TRANSFER |
| 183 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 192 DRIVE) |
| 184 | 1 | LOT, (4) FOOT CONTROLLERS (LOCATED ON BOTH SIDE OF LOT 183) |
| 185 | 1 | LOT, STEEL FRAMED, WOOD COVERED PLATFORM AROUND ENTIRE BREWCO LINE |
| 188 | 1 | APPROX. 45' TROUGHING ROLL BELT CONVEYOR FRAME W/CATWALK, LADDER, (2) STEEL LOGS, & NO DATA FALK DRIVE |
| 189 | 1 | APPROX. 95' H78 CHAIN CONVEYOR FEED CHIP BIN W/H&T SPROCKETS, STEEL TROUGH, NO DATA GEARHEAD MOTOR, & (1) STEEL LEG |
| 190 | 1 | APPROX. 160' X 20" BELT CONVEYOR FEEDING HOG FUEL BIN W/H&T DRUMS, TAKE-UP DRUM, & BELT SWEEPS (NO DRIVES) |
| 191 | 1 | SKK 1 HP/68 RPM BELT SWEEP GEARHEAD MOTOR |
| 192 | 1 | SKK 1 HP/68 RPM BELT SWEEP GEARHEAD MOTOR |
| 193 | 1 | SKK 15 HP/68 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 190 DRIVE) |
| 194 | 1 | 28' H78 CHAIN FINES CONVEYOR W/H&T DRUMS, & STEEL TROUGH |
| 195 | 1 | 26' H78 CHAIN BELT SWEEPS CONVEYOR W/H&T DRUMS, & STEEL TROUGH |
| 196 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 194 DRIVE) |
| 197 | 1 | SKK 3 HP/56 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 195 DRIVE) |
| 198 | 1 | 8'X8' WELDED & BOLTED SURGE BIN W/(2) AUGER CLEAN OUTS, MOTOR, & REDUCER |
| 199 | 1 | PRECISION PCS8X8 3-DECK CHIP SHAKER SCREEN W/DRIVE MOTOR (SPARE PARTS SOLD AT LOT 360) |
| 200 | 1 | 50' H78 CHAIN OVERS CONVEYOR W/H&T SPROCKETS, STEEL TROUGH, & G.E. GEARHEAD MOTOR |
| 201 | 1 | APPROX. 45' H110 DRAG CHAIN CHIPPER CLEAN-OUT CONVEYOR W/H&T SPROCKETS & STEEL TROUGH |
| 202A | 1 | SKK 5 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 201 DRIVE) |
| 202B | 1 | WOOD & STEEL FRAMED STRUCTURE OVER CHIPPER & CHIPPER INFEED |
| 203 | 1 | WEST SALEM MACHINE 66" 8-KNIFE HORIZONTAL FEED, BOTTOM DISCHARGE CHIPPER W/250 HP DRIVE MOTOR |
| 204 | 1 | 22'X24" VIBRATORY CONVEYOR W/STEEL & FIBERGLASS TROUGHS, & DRIVE MOTOR |
| 205 | 1 | RENS METAL DETECTOR W/SEARCH COIL, & ELECTRICS |
| 206 | 1 | WILLIAMS 460 SERIES-5 DROP FEED, BOTTOM DISCHARGE HAMMER HOG W/INFEED CHUTE |
| 207A | 1 | WESTINGHOUSE 500 HP/885 RPM/460V CHIPPER DRIVE MOTOR |
| 207B | 1 | LOT, HOG HAMMERS |
| 208 | 1 | 11' TWIN-STRAND DRAG CHAIN HOG CLEAN-OUT CONVEYOR W/H&T SPROCKETS, & STEEL TROUGH |
| 209 | 1 | SKK 5 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 208 DRIVE) |
| 210 | 1 | LOT, STEEL STRUCTURE AROUND HOG W/STAIRWAY TO HOG FEED CONVEYOR |
| 212 | 1 | G.E. 800 AMP ADJUSTABLE TRIP CIRCUIT BREAKER |
| 213 | 1 | LOT, G.E. 3-SECTION MCC W/ATTACHED BOXES, & DISCONNECT UNDER LOT 212 BREAKER |
| 214 | 1 | LOT, (5) ASSORTED ELECTRIC BOXES ON WALL |
| 215 | 1 | IES 250 HP SOLID STATE REDUCED VOLTAGE STARTER |
| 216 | 1 | G.E. 500 HP REDUCED VOLTAGE STARTER |
| 217 | 1 | 92'X30" BELT CONVEYOR FEEDING HOG W/H&T DRUMS, TAKE-UP DRUM, MOTORIZED BELT SWEEP, & CATWALK |
| 218 | 1 | NO DATA GEARHEAD MOTOR W/DRIVE CHAIN (LOT 217 DRIVE) |
| 219 | 1 | RENS METAL DETECTOR W/SEARCH COIL, & ELECTRICS (ON LOT 217) |
| 220 | 1 | PEDESTAL MOUNT LOADER W/GRAPPLE, & 60 HP PUMP |
| 221 | 1 | LOT, ELECTRICAL CONTENTS OF PUMP HOUSE |
| 222 | 1 | 60 HP POND PUMP |
| 223 | 1 | 40 HP POND PUMP |
| 224 | 1 | 60 HP PUMP STARTER |
| 225 | 1 | 40 HP PUMP STARTER |
| 226 | 1 | 5' HORIZONTAL RECEIVER TANK W/PIPE TO UNION |
| 227 | 1 | 42' H112 DRAG CHAIN WASTE CONVEYOR W/H&T SPROCKETS, & STEEL TROUGH |
| 228 | 1 | SKK 3 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 227 DRIVE) |
| 229 | 1 | APPROX. 21'X3" WASTE BELT CONVEYOR W/CHEVRON BELT, H&T DRUMS, & STEEL TROUGH |
| 230 | 1 | SKK 5 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN, & DISCONNECT SWITCH (LOT 229 DRIVE - PLEASE PREVIEW) |
| 231 | 1 | THERMAL TRANSFER HYDRAULIC SUPPORT UNIT W/(2) 30 HP PUMPS, & ATTACHED ELECTRICS (FOR SCHURMAN EDGER) |
| 232 | 1 | APPROX. 105' LINK CHAIN WASTE CONVEYOR W/7/8" X 7-1/2" LINKS, 16" FLITES, H&T SPROCKETS, S-DRIVE, & STEEL TROUGH |
| 233 | 1 | SKK 7-1/2 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 232 DRIVE) |
| 234 | 1 | LOT, CONVEYOR BELTING & MISC. |
| 235 | 1 | 85' X 24" WASTE BELT CONVEYOR W/H&T DRUMS, STEEL TROUGH, SLOPES, & NO DATA G.E. GEARHEAD MOTOR (PLEASE PREVIEW) |
| 236 | 1 | 28' H78 CHAIN WASTE CONVEYOR W/H&T SPROCKETS, & STEEL TROUGH |
| 237 | 1 | SKK 2 HP/45 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 236 DRIVE) |
| 238 | 1 | HIMMEL NO DATA GEARHEAD MOTOR W/DRIVE CHAIN (TRASH DECK DRIVE) |
| 239 | 1 | HYDRAULIC SUPPORT UNIT W/(2) 40 HP PUMPS (FOR RESAW AREA) |
| 240 | 1 | HYDRAULIC SUPPORT UNIT W/25 HP PUMP (KOCKUMS RESAW) |
| 241 | 1 | HYDRAULIC SUPPORT UNIT W/(2) 40 HP PUMPS |
| 242 | 1 | INGERSOLL RAND 242-50 5 HP 3-PH TANK MOUNTED AIR COMPRESSOR |
| 243 | 1 | G.E. 250 HP/575 RPM SLIP RING HEAD RIG DRIVE MOTOR W/GRID & DRUM STARTER (LOCATED UPSTAIRS - NO DRIVE BELTS INCLUDED) |
| 244 | 1 | IES 200 HP SOLID STATE REDUCED VOLTAGE STARTER (PARTS ARE MISSING) |
| 245 | 1 | LOT, (35) ASSORTED ELECTRIC BOXES (LOCATED BETWEEN LOT 244 & AIR COMPRESSOR) |
| 246 | 1 | HYDRAULIC SUPPORT UNIT W/60 HP PUMP |
| 247 | 1 | HYDRAULIC SUPPORT UNIT W/40 HP PUMP |
| 248 | 1 | EMPTY ELECTRICAL ENCLOSURE |
| 249 | 1 | CUTLER HAMMER SIZE 4 STARTER W/150 AMP BREAKER |
| 250 | 1 | LOT, G.E. SIZE 4 STARTER W/DISCONNECT SWITCH & TRANSFORMER |
| 251 | 1 | LOT, STEEL SAWMILL FLOOR & SUBSTRUCTURE |
| 252 | 1 | LOT, ELECTRICAL WIRE |
| 253 | 1 | LINEAR POSITIONING WAND |
| 254 | 1 | LINEAR POSITIONING WAND |
| 255 | 1 | LINEAR POSITIONING WAND |
| 256 | 1 | LINEAR POSITIONING WAND |
| 257 | 1 | LINEAR POSITIONING WAND |
| 258 | 1 | LINEAR POSITIONING WAND |
| 259 | 1 | ALLEN BRADLEY LOT, PLC BOARDS |
| 260 | 1 | LOT, ASSORTED ELECTRICAL PARTS & SUPPLIES (REMAINING LOOSE CONTENTS OF ROOM) |
| 261 | 1 | LOT, EDGER SAW BLADES |
| 262 | 1 | LOT, EDGER SAW BLADES |
| 263 | 1 | LOT, EDGER SAW BLADES W/RACK |
| 264 | 1 | LOT, EDGER SAW BLADES |
| 265 | 1 | LOT, EDGER SAW BLADES |
| 266 | 1 | BABBIT JIG |
| 267 | 1 | BABBIT JIG |
| 268 | 1 | LOT, (2) BABBIT JIGS |
| 269 | 1 | LOT, BABBIT POT W/LADLES, & EXHAUST HOOD |
| 270 | 1 | LOT, EDGER ARBOR COLLARS |
| 271 | 1 | LOT, STRETCHER ROLLS |
| 272 | 1 | ARMSTRONG 6900 LOT, (2) SHAPERS |
| 273 | 1 | ARMSTRONG 53 PNEUMATIC SWAGE |
| 274 | 1 | ARMSTRONG 53 PNEUMATIC SWAGE |
| 275 | 1 | ARMSTRONG 6900BA PNEUMATIC SHAPER |
| 276 | 1 | LOT, EDGER GUIDES |
| 277 | 1 | LOT, ASSORTED FILING ROOM PARTS & SUPPLIES IN CABINETS |
| 278 | 1 | EDGER-GUIDE BABBIT MILLING MACHINE |
| 279 | 1 | SQUARE-D SIZE 6 STARTER W/800 AMP BREAKER |
| 280 | 1 | LOT, REMAINING ELECTRIC BOXES ON WALL W/30 AMP DISCONNECT SWITCH BEHIND SIZE 6 STARTER |
| 281 | 1 | CME 41 BENT KNIFE GRINDER |
| 282 | 1 | HANCHETT SIZE DN40 TRAVELING BED STRAIGHT KNIFE GRINDER |
| 283 | 1 | BABBIT POT W/LADLES, & EXHAUST HOOD |
| 284 | 1 | LOT, BABBITS |
| 285 | 1 | LOT, FILING ROOM TOOLING |
| 286 | 1 | 1-PH CHAIN SAW SHARPENER |
| 287 | 1 | ARMSTRONG CAM WHEEL |
| 288 | 1 | 6"X17" DIA. ANVIL |
| 289 | 1 | 6" BENCH VISE |
| 290 | 1 | GUIDE CUTTER |
| 291 | 1 | BOTTLE CART |
| 292 | 1 | LOT, FILING ROOM PARTS & SUPPLIES (CONTENTS OF CABINETS) |
| 293 | 1 | ARMSTRONG 4RH BANDSAW SHARPENER W/CLAMP & STANDS |
| 294 | 1 | HOE SAW GUIDE SHAPER |
| 295 | 1 | ACME CIRCULAR SAW HAND GUMMER |
| 296 | 1 | ARMSTRONG 6RH BANDSAW SHARPENER W/CLAMP & STANDS |
| 297 | 1 | LOT, ASSORTED FILING ROOM PARTS & SUPPLIES IN (2) CABINETS BY TWO BANDSAW SHARPENERS |
| 298 | 1 | LOT, (4) HEAD RIG SAWBLADES W/(3) CARTS |
| 299 | 1 | LOT, (4) RESAW SAWBLADES W/(1) CART |
| 300 | 1 | LOT, BANDSAW STRETCHER ROLL W/WELDING CLAMP, & LEVELING BLOCK |
| 301A | 1 | LOT, PARTICLE BOARD |
| 301B | 1 | LOT, ALUMINUM FLAT BAR |
| 301C | 1 | LOT, ASSORTED EQUIPMENT FILTERS |
| 302 | 1 | GENCO 250 HP CARRIAGE DRIVE W/250 HP MG SET, 7-/2 HP COOLING BLOWER, CABLE SPOOL, END SPOOLS, & CABLE |
| 303 | 1 | GENCO 304 250 HP REDUCED VOLTAGE STARTER |
| 305 | 1 | LOT, ASSORTED MILL PARTS & SUPPLIES W/WOOD SHELF |
| 306 | 1 | LOT, HYDRAULIC HOSE (ON 3 PALLETS) |
| 307 | 1 | LOT, DRIVE BELTS |
| 308 | 1 | ALLEN BRADLEY SIZE 6 STARTER |
| 309 | 1 | ALLEN BRADLEY SIZE 5 STARTER |
| 310 | 1 | LOT, ASSORTED TRANSFORMERS |
| 311 | 1 | LOT, ASSORTED ELECTRIC BOXES (ON 2 PALLETS) |
| 312 | 1 | LOT, SLABBER PARTS |
| 313 | 1 | LOT, CARRIAGE CABLE |
| 314 | 1 | LOT, CHIPPER PARTS |
| 315 | 1 | SINGLE SECTION OF ADJUSTABLE PALLET SHELVING |
| 316 | 1 | 15 HP BLOWER W/BLOW PIPE |
| 317 | 1 | 3 HP MOTOR W/REDUCER |
| 318 | 1 | LOT, DEBARKER RING ASSEMBLY W/CYLINDER & ARM |
| 319 | 1 | 30' 3-STRAND H78 CHAIN TRANSFER W/H&T SPROCKETS, S-DRIVE, & STEEL RACES |
| 320 | 1 | HITACHI 7-1/2 HP/40 RPM GEARHEAD MOTOR W/DRIVE CHAIN (LOT 319 DRIVE) |
| 321 | 1 | LOT, ASSORTED FEED ROLLS |
| 322 | 1 | LOT, CARRIAGE KNEE BED PLATES |
| 323 | 1 | LOT, MACHINERY ARBORS |
| 324 | 1 | LOT, ELECTRICAL WIRE |
| 325 | 1 | HITACHI 7-1/2 HP/40 RPM GEARHEAD MOTOR |
| 326 | 1 | HITACHI 7-1/2 HP/40 RPM GEARHEAD MOTOR |
| 327 | 1 | 10 HP MOTOR W/LINKBELT 68 RPM REDUCER |
| 328 | 1 | TOSHIBA 350 HP/1770 RPM MOTOR |
| 329 | 1 | YASKAWA 40 HP/3515 RPM MOTOR |
| 330 | 1 | FAIRBANKS MORSE 40 HP/1765 RPM MOTOR |
| 331 | 1 | TOSHIBA 25 HP/1760 RPM MOTOR |
| 332 | 1 | RELIANCE 15 HP MOTOR |
| 333 | 1 | TOSHIBA 10 HP/1165 RPM MOTOR |
| 334 | 1 | TOSHIBA 10 HP/3510 RPM MOTOR |
| 335 | 1 | TOSHIBA 10 HP/1730 RPM MOTOR |
| 336 | 1 | TECO 10 HP/1740 RPM MOTOR |
| 337 | 1 | TECO 10 HP/3470 RPM MOTOR |
| 338 | 1 | ELECTRIC MOTOR |
| 339 | 1 | LOT, ELECTRIC MOTORS ON PALLET |
| 340 | 1 | LOT, ELECTRIC MOTORS ON PALLET |
| 341 | 1 | LOT, STARTERS ON PALLET |
| 343 | 1 | LOT, CONVEYOR BELTING |
| 344 | 1 | LOT, SHEAVES |
| 345 | 1 | LOT, CONVEYOR DRUMS |
| 346 | 1 | LOT, EDGER GUIDES |
| 347 | 1 | LOT, PLANER GUIDES |
| 348 | 1 | 7' SLAT CHAIN CONVEYOR |
| 349 | 1 | LOT, BABBIT BEARINGS |
| 350 | 1 | LOT, SPROCKETS |
| 351 | 1 | LOT, ASSORTED CYLINDERS ON PALLET |
| 352 | 1 | LOT, ASSORTED CYLINDERS ON PALLET |
| 353 | 1 | LOT, ASSORTED CYLINDERS ON PALLET |
| 354 | 1 | LOT, ASSORTED CYLINDERS ON PALLET |
| 355 | 1 | LOT, HYDRAULIC MOTORS ON PALLET |
| 356 | 1 | LOT, H124 CHAIN |
| 357 | 1 | LOT, H132 CHAIN |
| 358 | 1 | LOT, ASSORTED CHAIN |
| 359 | 1 | LOT, YARD LIGHTS |
| 360 | 1 | LOT, CHIP SHAKER SCREENS |
| 361 | 1 | HEAD RIG BAND WHEEL |
| 362 | 1 | FIRE HOSE CART |
| 363 | 1 | LOT, UHMW FLITES |
| 364 | 1 | LOT, FIRE EXTINGUISHERS |
| 365 | 1 | SA WOODS 415M 15"X6" PLANER W/125 HP FEED ROLL DRIVE, & BOX OF PARTS W/SIDE HEAD ASSEMBLY |
| 366 | 1 | CAT 966E HRT ARTICULATED FRONT END LOADER W/BALDERSON LOG FORKS, 6-CYL DIESEL, 4-SPEED POWERSHIFT TRANSMISSION HOURS: 18,800 99Y07077 |
| 367 | 1 | SLIP-ON LOADER BUCKET |
| 368 | 1 | LOT, (4) COE 34'X120'X20' HIGH OVERSIZED DOUBLE TRACK STEAM HEATED DRY KILNS W/3 ZONE PER KILN, LINE SHAFT FANS (W/FRONT & BACKSIDE 60 HP DRIVE MOTORS), COE RECORDERS, VALVES, CUTLER HAMMER EATON ELECTRICS, 10'X136' KILN CONTROL HOUSE (W/ASSOCIATED PIPING VALVES, CATWALK & STAIRS). KILN #9 COMES WITH COMPLETE FRAMEWORK, BUT NO SKIN ON WALL ATTACHED TO KILN #8. *SOLD SUBJECT TO CONFIRMATION* |
| 369 | 1 | MOORE LOT, (2) 34'X120'X20' HIGH OVERSIZE DOUBLE TRACK STEAM HEATED DRY KILNS, 3 ZONES PER KILN, 7-1/2 HP FANS, MOORE RECORDERS, CONTROLS, 10'X15' CONTROL HOUSE, ASSOCIATED PIPING, VALVES, & CATWALK KILN #7 SOLD MINUS COMMON WALL W/KILN #6. *SOLD SUBJUCT TO CONFIRMATION* |
| 370 | 1 | NEWMAN DROP FEED, BOTTOM DISCHARGE HAMMER HOE |
| 371 | 1 | MID-OREGON MINI-HOG W/20 HP DRIVE MOTOR, & INFEED BELT CONVEYOR |
| 372 | 1 | KVAL SIDE HEAD MACHINE |
| 373 | 1 | FLYING CUT-OFF SAW |
| 374 | 1 | MANN RUSSELL 6' R.F. GIVE MACHINE W/#700 46KVA GENERATOR |
| 375 | 1 | RAMCO 2ST-2 24" 2-HEAD TOP BELT SANDER W/50+10 HP BELT DRIVE MOTORS 1720 |
| 376 | 1 | RAMCO 2SB-2 24" 2-HEAD BOTTOM BELT SANDER W/50+10 HP BELT DRIVE MOTORS 1721 |
| 377 | 1 | LOT, SANDER MOTOR STARTERS |
| 378 | 1 | TURNER 60" HORIZONTAL BAND RESAW W/DRIVE MOTOR |
| 379 | 1 | 21-1/2' BELT CONVEYING TABLE W/GEARHEAD MOTOR |
| 380 | 1 | CHASE INDUSTRIES IMPULSE SEALER W/FEED THRU BELT CONVEYOR |
| 381 | 1 | CHASE INDUSTRIES 1200 WATT SHRINK WRAP TUNNEL W/FEED THRU TRANSFER |
| 382 | 1 | LOT, GRAVITY ROLLCASE W/4-STRAND BELT TRANSFER, & GEARHEAD MOTOR |
| 383 | 1 | TONGUE & GROOVE MACHINE W/FEED THRU SLAT CHAIN TRANSFER, & CROSS OVER BELT CONVEYOR |
| 384 | 1 | ONSRUD MACHINE WORKS TYPE WASOAB SHAPER W/ARO AUTO DRILL |
| 385 | 1 | T-III SAW |
| 386 | 1 | 7'X49" BELT TRANSFER W/HYDRAULIC DRIVE MOTOR |
| 387 | 1 | BLACK BROTHERS 220-500 20" GLUE SPREADER 181758 |
| 388 | 1 | SPERRY 15 HP WINCH |
| 389 | 1 | INDUSTRIAL FJS25 FINGER JOINT LINE |
| 390 | 1 | INDUSTRIAL FJA200 FLYING CUT OFF SAW W/ASSEMBLY TABLE |
| 391 | 1 | AMERICAN FINISHING SYSTEMS SPRAY BOOTH |
| 392 | 1 | AMERICAN FINISHING SYSTEMS SPRAY BOOTH |
| 393 | 1 | GRACO PNEUMATIC PAINT PUMP |
| 394 | 1 | GRACO PNEUMATIC PAINT PUMP |
| 395 | 1 | 4-HEAD PAINT LINE BUFFER |
| 396 | 1 | LOT, ASSORTED PAINT LINE CONVEYING EQUIPMENT W/GEARHEAD MOTORS |
| 397 | 1 | MDI SEARCH COIL |
| 398 | 1 | CM VALVESTAR ELECTRIC CHAIN HOIST |
| 399 | 1 | LOT, PLANER HEADS |
| 400 | 1 | GLUE PUMP |
| 401 | 1 | LOT, LIGHTS |
| 402 | 1 | LINCOLN 300 AMP DC ARC WELDER |
| 403 | 1 | 2 HP/1-PH TANK MOUNTED AIR COMPRESSOR |
| 404 | 1 | TAYLOR GLUE SPREADER W/SLAT CHAIN FEED TABLE |
