|
LOT# |
QTY. |
DESCRIPTION |
| 1 | 1 | BENCH VISE W/STEEL TABLE |
| 2 | 1 | LOT, ASSORTED GREASE |
| 3 | 1 | LOT, FLEXCO BELT FASTENERS/ TATCH-A-CLEAT BELT CLEATING |
| 4 | 1 | LOT, RUBBER CONVEYOR DRUM COVERING |
| 5 | 1 | LOT, (2) DODGE SIZE 2-15/16" PILLOW BLOCK BEARINGS |
| 6 | 1 | LOT, ASSORTED BEARINGS ON BOTTOM SHELF |
| 7 | 1 | LOT, KEY KNIFE STOCK |
| 8 | 1 | LOT, SAFETY HARNESSES |
| 9 | 1 | SINGLE PHASE SUMP PUMP |
| 10 | 1 | LOT, (2) ALLEN BRADLEY SIZE 3 MAG STARTERS, 709 SERIES |
| 11 | 1 | LOT, JET OR1412, 14"-5 SPD DRILL PRESS W/VISE |
| 12 | 1 | MILLER SRN333 DC ARC WELDER W/WELDING HOOD |
| 13 | 1 | LOT, CLEAN-UP & ASSORTED YARD TOOLS |
| 14 | 1 | OXY/ACET SET W/CART |
| 15 | 1 | NIELSEN 1 PHASE CHAIN SAW SHARPENER |
| 16 | 1 | DAYTON 1HP/1 PHASE DOUBLE END GRINDER |
| 17 | 1 | MOTOR CONTROL CABINET W/225 AMP MAIN BREAKER, CUTLER HAMMER AF93 ADJUSTABLE FREQUENCY DRIVE, ASSORTED MAG STARTERS |
| 18 | 1 | HITACHI J3000 IGBT INVERTER |
| 19 | 1 | LOT, ASSORTED MILL PARTS & SUPPLIES UPSTAIRS & BEHIND START OF SALE TABLE |
| 20 | 1 | LOT, METAL BINS W/ASSORTED FASTERNERS |
| 21 | 1 | LOT, ASSORTED HYDRAULIC PUMPS & MOTORS |
| 22 | 1 | LOT, ASSORTED MILL PARTS & SUPPLIES W/REFRIGERATOR (REMAINING UNSOLD CONTENTS OF AREA) |
| 23 | 1 | LOT, ASSORTED MILL PARTS & SUPPLIES (LOOSE CONTENTS OF ROOM) |
| 24 | 1 | QUINCY NORTHWEST QNW360-1 75HP ROTARY SCREW AIR COMPRESSOR 840618 |
| 25 | 1 | PACIFIC FLUID SYSTEM HYDRAULIC SUPPORT UNIT W/(4) 50HP PUMPS, (1) 3HP PUMP, HEAT EXCHANGER |
| 26 | 1 | 225 GALLON HYDRAULIC OIL TANK |
| 27 | 1 | HI-TEST 2-TON CAP. MANUAL CHAIN HOIST W/TROLLEY & RAIL (NO TORCHES) |
| 28 | 1 | 4-SECTION MOTOR CONTROL W/(1) SQUARE D, SIZE 5 REDUCED VOLTAGE, (2) SQUARE D, SIZE 4 REDUCED VOLTAGE, (1) ALLEN BRADLEY SIZE 4 MAG STARTER |
| 29 | 1 | ALLEN BRADLEY SIZE 4 MAG STARTER (709 SERIES) |
| 30 | 1 | LOT, (6) MARKED DISCONNECT SWITCHES |
| 31 | 1 | LOT, ASSORTED TRANSFORMERS & ELECTRIC BOXES W/LOCK OUT STAND |
| 32 | 1 | RSE-SIERRA 3000 AMP-480Y/277 VOLT, 3 PHASE GROUND FAULT BREAKER PANEL |
| 33 | 1 | SIEMENS-ALLIS 400HP REDUCED VOLTAGE STARTER |
| 34 | 1 | SIEMENS-ALLIS 400HP REDUCED VOLTAGE STARTER |
| 35A | 1 | SQUARE D 6-SECTION-29 STATION MOTOR CONTROL CENTER |
| 35B | 1 | SIXTRAK PLC CABINET |
| 35C | 1 | LOT, ASSORTED MILL PARTS & SUPPLIES, OFFICE FURNITURE (LOOSE CONTENTS OF OFFICE) |
| 36 | 1 | 30'-6 STRAND H124 CHAIN LOG DECK W/H&T SPROCKETS, S-DRIVE, STEEL RACES W/INFEED STEEL SLIDE, LOG STOP & LOADER, MARKED STEEL SUPPORTS |
| 37 | 1 | SKK 10HP/25 RPM GEARHEAD MOTOR W/ DRIVE CHAIN (LOT 36 DRIVE) |
| 38 | 1 | PEDESTAL MOUNT HYDRAULIC OPERATED LOG LOADER W/GRAPPLE |
| 39 | 1 | 80'-H112 DRAG CHAIN LOG HAUL CONVEYOR W/H&T SPROCKETS, HEAD HOURGLASS ROLL, S-DRIVE, STEEL LEGS TO FIRST HORIZONTAL I- BEAM |
| 40 | 1 | SKK 20HP/45 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 39 DRIVE) |
| 41 | 1 | 1996 NICHOLSON A5A-LH 6-TOOL AIR SEAL RING DEBARKER W/100HP AC RING DRIVE, 80HP FEED ROLL DRIVE, SLIDE OUT RING, SHED DOWNSTAIRS W/LUBE SYSTEM |
| 42 | 1 | LOT, DEBARKER PARTS LOCATED ON GROUND, UNDER DEBARKER (SOLD BY PICTURE-PLEASE PREVIEW) |
| 43 | 1 | LOT, JOY STICK CONTROLLERS, 2- PUSH BUTTON CONTROL PANELS W/ CHAIR IN CONTROL BOOTH |
| 44 | 1 | LOT, SIXTRAK PROGRAMMABLE CONTROL PANEL FOR CHIPPING LINE (LOCATED IN CONTROL BOOTH) |
| 45 | 1 | 6'X15' CONTROL BOOTH W/LIGHTS & AIR CONDITIONER |
| 46 | 1 | LOT, STEEL PLATFORM UNDER CONTROL BOOTH W/SUPPORTS TO GROUND, 3 ATTACHED SECTIONS OF STAIRS |
| 47 | 1 | LOT, ALL EXPANDED METAL CATWALK ALONG DEBARKER/CHIPPER LINE W/2-SECTIONS OF STAIRWAY (1 STAIRWAY BY DEBARKER INFEED 1 STAIRWAY BY CHIPPER INFEED) NO SUBSTRUCTURE |
| 48 | 1 | 53'-H112 DRAG CHAIN DEBARKER OUTFEED LOG HOUSE CONVEYOR W/ H&T SPROCKETS, S-DRIVE, STEEL TROUGH, HOURGLASS INFEED ROLL, STEEL SIDE WALL (NO SUBSTRUCTURE) |
| 49 | 1 | WESTINGHOUSE 15HP/38.4:1 RATIO GEARHEAD MOTOR W/DRIVE CHAIN (LOT 48 DRIVE) |
| 50 | 1 | 123'-WD118 DRAG CHAIN LOG HAUL CONVEYOR W/H&T SPROCKETS, S- DRIVE, STEEL TROUGH, SUPPORTS TO GROUND |
| 51 | 1 | SKK 15HP/68 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 50 DRIVE) GEARHEAD RATED 37HP |
| 52 | 1 | 1996 NICHOLSON 96"-6 KNIFE HORIZONTAL OVER CENTER FEED, HORIZONTAL SIDE DISCHARGE WHOLE LOG CHIPPER W/24"X36" THROAT, HYDRAULIC START ASSIST, DRIVE BELTS S2655R |
| 53 | 1 | LOT, CHIPPER PARTS |
| 54 | 1 | G.E. 400HP/1170 RPM/440 VOLT CHIPPER DRIVE MOTOR (NO BELTS) |
| 55 | 1 | G.E. 400HP/1170 RPM/440 VOLT CHIPPER DRIVE MOTOR (NO BELTS) |
| 56 | 1 | SIEMENS 800 AMP ADJUSTABLE TRIP CIRCUIT BREAKER |
| 57 | 1 | SIEMENS 800 AMP ADJUSTABLE TRIP CIRCUIT BREAKER |
| 58A | 1 | 25'X14' CHIPPER BUILDING W/ WELDED STEEL FRAME, SUPPORTS TO GROUND |
| 58B | 1 | CUTLER HAMMER AF93 20HP ADJUSTABLE FREQUENCY MOTOR CONTROLLER (DOWNSTAIRS) |
| 59 | 1 | 40'X5' CHIPPER CLEAN OUT TROUGHING ROLL BELT CONVEYOR |
| 60 | 1 | SKK 7-1/2HP/68 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 59 DRIVE) |
| 61 | 1 | SHUTTE #90B2 #1-1/2 DROP FEED, BOTTOM DISCHARGE RE-CHIPPING HAMMER MILL W/75HP DRIVE MOTOR |
| 62 | 1 | LOT, HAMMER MILL PARTS |
| 63 | 1 | STEEL SUPPORT STAND UNDER HAMMER MILL |
| 64 | 1 | APPROX. 60'X36" HAMMER MILL CLEAN OUT TROUGHING ROLL BELT CONVEYOR W/CHEVRON STYLE BELT, BOLT TOGETHER FRAME |
| 65 | 1 | SKK 7-1/2HP/68 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 64 DRIVE) |
| 66 | 1 | 10'X10'XAPPROX. 10' SURGE BIN W/TWIN AUGER CLEAN OUT, SKK GEARHEAD MOTOR, SUPPORTS TO GROUND |
| 67 | 1 | BM&M 8'X20'-3 DECK CHIP SHAKER SCREEN W/DRIVE MOTOR, SUPPORTS TO GROUND 5649 |
| 68 | 1 | 25'X53" SCREEN CLEAN OUT TROUGHING ROLL BELT CONVEYOR |
| 69 | 1 | SKK 7-1/2HP/100 RPM GEARHEAD MOTOR DRIVE CHAIN (LOT 68 DRIVE) |
| 70 | 1 | APPROX. 85'X60" RADIAL ARM STACKER TROUGHING ROLL BELT CONVEYOR W/FALK BELT DRIVE, SKK 3HP/16-1/2 RPM RUBBER TIRE TRAVEL DRIVE |
| 71A | 1 | LOT, ALL CONCRETE ECOLOGY BLOCKS AT MILL SITE |
| 71B | 1 | LOT, ASSORTED SPLIT FIREWOOD BY ECOLOGY BLOCKS |
| 72 | 1 | 35'X20" OVERS BELT CONVEYOR W/ H&T DRUMS, BOLT TOGETHER STEEL TROUGH |
| 73 | 1 | SKK 7-1/2HP/84 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 72 DRIVE) |
| 74 | 1 | 72'-H104 DRAG CHAIN CONVEYOR W/H&T SPROCKETS, STEEL TROUGH |
| 75 | 1 | 50'-H104 DRAG CHAIN CONVEYOR W/H&T SPROCKETS, STEEL TROUGH |
| 76 | 1 | SKK 7-1/2HP/68 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 74 DRIVE) |
| 77 | 1 | SKK 10HP/88 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 75 DRIVE) |
| 78 | 1 | HYDRAULIC OPERATED LOG SPLITTER, 18' OPENING W/(2) 10' HYDRAULIC RAMS |
| 79 | 1 | DIESEL HYDRAULIC POWER UNIT FOR SPLITTER W/4 CYL GM DIESEL ENGINE |
| 80 | 1 | DIESEL FUEL TANK W/STAND, GRAVITY FLOW NOZZLE |
| 81 | 1 | 500 GALLON FIRE FIGHTING TRAILER MOUNTED WATER TANK W/ GAS FIRED PUMP, REEL |
| 82 | 1 | 50'X33" WHEELED TROUGHING ROLL BELT CONVEYOR STACKER W/3 PHASE ELECTRIC MOTOR, SHAFT MOUNTED REDUCER |
| 83 | 1 | LOT, ASSORTED STRUCTURAL STEEL |
| 84 | 1 | RAMEY HYDRAULIC OPERATED LOG LOADER W/SWIVEL GRAPPLE (NO HYDRAULIC UNIT) |
| 85 | 1 | 14'-5 STRAND H124 CHAIN LOG DECK W/H-SHAFT, T SPROCKETS, STEEL RACES |
| 86 | 1 | SKK 10HP/25 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 85 DRIVE) |
| 87 | 1 | 20'-H132 CHAIN LOG HAUL CONVEYOR W/EXPANDED METAL CATWALK, MOTOR & REDUCER |
| 88 | 1 | PRESCOTT 5' BAR CHAIN LOG CUT-OFF SAW W/30HP SAW MOTOR, HYDRAULIC ACTUATED W/HYDRAULIC PUMP & RESERVOIR TANK, BLOCK FLIPPER, LOG HOLD DOWN CLAMP, CONTROLS & ELECTRICS |
| 89 | 1 | 10'-81XH CHAIN SAWDUST CONVEYOR W/G.E. PACIFIC 1HP/ 102 RPM GEARHEAD MOTOR |
| 90 | 1 | HYDRAULIC OPERATED FIREWOOD SPLITTER W/FOOT CONTROLLER, FLEX HYDRAULIC HOSES |
| 91 | 1 | 50HP HYDRAULIC PUMP W/BLUE RESERVOIR TANK |
| 92 | 1 | 50HP HYDRAULIC PUMP |
| 93 | 1 | 13'-H78 CHAIN TRANSFER W/ GEARHEAD MOTOR |
| 94 | 1 | 21'X18" CLEATED BELT CONVEYOR W/HYDRAULIC DRIVE MOTOR |
| 95 | 1 | LOT, FIREWOOD PROCESSING LINE ELECTRIC BOXES |
| 96 | 1 | STEEL & WOOD FRAMED, METAL COVERED STRUCTURE OVER FIREWOOD PROCESSING LINE W/LIGHTS, JIB BOOM (40'X30' BETWEEN UPRIGHTS) |
| 97 | 1 | MARR 8,000 LB CAP. LOG TRAILER LOADER W/PENDANT CONTROLS, ELECTRICS |
| 98 | 1 | PEERLESS HYDRAULIC OPERATED BARK STORAGE BIN W/HYDRAULIC SUPPORT UNIT, ELECTRICS |
| 99 | 1 | APPROX. 75' HD78 CHAIN CONVEYOR FEEDING BIN W/SKK 7-1/2HP/68 RPM GEARHEAD MOTOR, LEG SUPPORTS |
| 100 | 1 | WILLIAMS #40S DROP FEED, BOTTOM DISCHARGE HAMMER HOG W/INFEED CHUTE, DRIVE MOTOR (LOT INCLUDES SPARE ARBOR IN SHOP UNDER START OF SALE TABLE) |
| 101 | 1 | STEEL SUPPORT STRUCTURE UNDER HOG |
| 102 | 1 | APPROX. 68'X38" TROUGHING ROLL BELT CONVEYOR FEEDING HOG W/LEG SUPPORTS |
| 103 | 1 | SKK 7-1/2HP/68 RPM GEARHEAD MOTOR, DRIVE CHAIN (LOT 102 DRIVE) |
| 104 | 1 | 30'X60" DEBARKER CLEAN OUT TROUGHING ROLL BELT CONVEYOR |
| 105 | 1 | 5HP MOTOR W/FOOTE JONES 57.6:1 RATIO REDUCER, DRIVE CHAIN (LOT 104 DRIVE) |
| 106 | 1 | 6' VERTICAL AIR RECEIVER TANK |
| 107 | 1 | 6' VERTICAL AIR RECEIVER TANK |
| 108 | 1 | LOT, MARKED STEEL SUB STRUCTURE UNDER DEBARKER, DEBARKER INFEED CONVEYOR, DEBARKER INFEED LOG DECK |
| 109 | 1 | LOT, CONDUIT & WIRE ON PLANT SITE: EXCEPTIONS ARE: NO OVER HEAD HIGH VOLTAGE WIRE, NO WIRE ON HIGH VOLTAGE SIDE OF PAD MOUNT TRANSFER, NO WIRE IN OFFICE, NO WIRE IN SHOP BLDG. RELATING TO SHOP BUILDING INTEGRITY, NO INTERNAL WIRE ON ANY MACHINERY. NO INTERNAL WIRE W/ANY ELECTRIC BOXES, WIRE DISCONNECTS AT IN&OUT FEED LUGS ON ELECTRIC BOXES, LUGS STAY W/ELECTRIC BOXES. LOT STARTS AT OUTFEED LUGS OF 2 1200 AMP BREAKERS IN SHOP THAT ARE NOT IN SALE (SEE AL FOR FURTHER CLARIFICATION) |
| 110 | 1 | WELDED STEEL ROOF STRUCTURE W/CONTENTS |
| 111 | 1 | WHEELED BELT CONVEYOR W/18" WIDE CHEVRON BELT |
| 112 | 1 | 8'X4' SCALPER SCREEN W/DRIVE MOTOR, ELECTRICS |
| 113A | 1 | LOT, 12'X20" ROLLCASE W/AUGER, CONVEYOR TROUGH |
| 113B | 1 | LOT, SCRAP STEEL |
| 114 | 1 | 6'-9 STRAND 81X CHAIN TRANSFER |
| 115 | 1 | LOT, LOG BUNKS |
| 116 | 1 | FORK MOUNT WORK PLATFORM |
| 117 | 1 | LOT, CONVEYOR COVERS |
| 118A | 1 | SUNDSTRAND #60-8002 HYDRAULIC DRIVE MOTOR |
| 118B | 1 | LOT, MILL CHAIN, SPROCKETS, BELTING & MISCELLANEOUS |
| 119 | 1 | 2-DRAWER LATERAL FILE CABINET W/WOOD COVER |
| 120 | 1 | 2-DRAWER LATERAL FILE CABINET |
| 121 | 1 | 4-DRAWER FILE CABINET |
| 122 | 1 | 60" WOOD DESK W/CHAIR |
| 123 | 1 | WOOD CABINET |
| 126 | 1 | BLACK UPHOLSTERED SWIVEL ARM CHAIR |
| 127 | 1 | LOT, (2) BROWN UPHOLSTERED SWIVEL ARM CHAIRS |
| 128 | 1 | LOT, (2) WHITE MARKER BOARDS |
| 129 | 1 | LOT, TIME CLOCK W/RACK, EMPLOYEE IN/OUT BOARD |
| 130 | 1 | LOT, COFFEE POT & MICROWAVE (BAD LATCH ON MICROWAVE) |
| 131 | 1 | FOLDING TABLE |
| 132 | 1 | LOT, BOOKS, MISC OFFICE EQUIP. |
| 133 | 1 | REFRIGERATOR |
| 134 | 1 | FIRST AID KIT |
| 135 | 1 | LOT, ASSORTED LOOSE CONTENTS OF CABINETS IN ROOM |
| 136 | 1 | 2-DRAWER LATERAL FILE CABINET |
| 137 | 1 | 3-DRAWER LATERAL FILE CABINET |
| 138 | 1 | WOOD BOOKCASE |
| 139 | 1 | WOOD CORNER DESK |
| 140 | 1 | 72" WOOD DESK |
| 141 | 1 | BLACK UPHOLSTERED SWIVEL ARM CHAIR |
| 142 | 1 | GRAY UPHOLSTERED SWIVEL ARM CHAIR |
| 143 | 1 | CANON #B640 FAX PHONE |
| 144 | 1 | SCHURMAN #666 ROSSER HEAD DEBARKER SYSTEM (DISMANTLERS MUST PROVIDE OWN FIRE PROTECTION FOR THIS LOT) |
| 145 | 1 | THUNDERBIRD #636DL CRAWLER STROKE DELIMBER W/DENARCO HEAD 9081 |
| 146 | 1 | JOHN DEERE 992LC CRAWLER LOG LOADER W/SWIVEL GRAPPLE CK992DL005081 |
| 147 | 1 | LINKBELT #LS5800TL CRAWLER LOG LOADER W/SWIVEL GRAPPLE, DETROIT DIESEL 41G61003B |
| 148 | 1 | CATERPILLAR 950 ARTICULATED RUBBER TIRE FRONT END LOADER W/CHIP BUCKET, DIESEL ENGINE, POWER SHIFT TRANSMISSION 81J13064 |
| 149 | 1 | TEREX 72-71B ARTICULATED RUBBER TIRE FRONT END LOADER W/LOG FORKS, DETROIT DIESEL 67016 |
| 150 | 1 | TEREX 72-61AA ARTICULATED RUBBER TIRE FRONT END LOADER W/LOG FORKS, DETROIT DIESEL 67867 |
| 151 | 1 | TROJAN 4000 ARTICULATED RUBBER TIRE FRONT END LOADER W/CHIP BUCKET, CUMMINS NTC355 DIESEL 76-4156 |
| 152 | 1 | 1980 PETERBILT 351A T/A CHIP TRUCK, 20'X8'X7' DUMP BOX, CUMMINS DIESEL, FULLER TRANS K5666 |
| 153 | 1 | 1984 GMC SIERRA 2500 PICK UP TRUCK W/UTILITY BED, V8, GAS, AUTO 1GDGC24M7EJ527612 |
| 154 | 1 | LUMBER STACKING ROLLCASE |
| 155 | 1 | LUMBER STACKING ROLLCASE |
| 156 | 1 | LUMBER STACKING ROLLCASE |
| 157 | 1 | LUMBER STACKING ROLLCASE |
| 158 | 1 | LUMBER STACKING ROLLCASE |
| 159 | 1 | LUMBER STACKING ROLLCASE |
| 160 | 1 | LUMBER STACKING ROLLCASE |
| 161 | 1 | LUMBER STACKING ROLLCASE |
| 162 | 1 | LUMBER STACKING ROLLCASE |
| 163 | 1 | LUMBER STACKING ROLLCASE |
| 164 | 1 | LUMBER STACKING ROLLCASE |
| 165A | 1 | LUMBER STACKING ROLLCASE |
| 165B | 1 | LOT, ASSORTED SPLIT FIREWOOD |
| 166 | 1 | SINGULATOR DECK FRAME |
| 167 | 1 | LOT, SINGULATOR DECK CHAIN |
| 168 | 1 | LOT, ASSORTED STEEL TRANSFER FRAMES, TROUGH CONVEYOR FRAMES |
| 169 | 1 | BAR CHAIN LUMBER UNIT CUT-OFF SAW W/7', 15HP SAW BAR, HYDRAULIC ACTUATED W/HYDRAULIC SUPPORT UNIT, 27'X51" LUMBER UNIT SPIRAL ROLLCASE W/HYDRAULIC DRIVE MOTOR |
| 170 | 1 | POULSEN 36 TRAVELING HORIZONTAL HEAD RIG BANDMILL, 36" DIA. BANDWHEELS, 50HP BANDMILL DRIVE, HYDRAULIC STRAIN, HYDRAULIC SHIFTING, UNI-OP TOUCH PAD CONTROLS, FORWARD & REVERSE SAW TRAVEL, STATIONARY CARRIAGE W/5 POSITION PRESET SETWORKS |
| 171 | 1 | 7'-3 STRAND H78 CHAIN TRANSFER |
| 172 | 1 | MARATHON 18" SASH GANG RESAW W/ HYDRAULIC SUPPORT UNIT |
| 173 | 1 | TREATED POLE |
| 174 | 1 | 18'X30" CHAIN DRIVEN ROLLCASE W/7-1/2HP MOTOR/REX PLANT GEAR 48 RPM REDUCER |
| 175 | 1 | 18'X36" CHAIN DRIVEN ROLLCASE W/5HP MOTOR/REX PLANT GEAR 48 RPM REDUCER |
| 176 | 1 | TIPPLE GATE W/CYLINDER |
| 177 | 1 | GENERAL MACHINE STICKER SAW W/30HP ARBOR MOTOR |
| 178 | 1 | SHAFT W/H78 SPROCKETS |
| 179 | 1 | 27'X24" BELT CONVEYOR W/ ATTACHED ELECTRICS |
| 180 | 1 | APPROX. 250 GALLON TANK |
| 181 | 1 | LOT, STRUCTURAL STEEL |
| 182 | 1 | LOT, SCRAP STEEL |
| 183 | 1 | SKK 7-1/2HP/30 RPM GEARHEAD MOTOR |
| 184 | 1 | SKK 3HP/45 RPM GEARHEAD MOTOR |
| 185 | 1 | SKK 5HP GEARHEAD MOTOR |
| 186 | 1 | 7-1/2HP MOTOR W/U.S. 45 RPM REDUCER |
| 187 | 1 | U.S. 100 RPM REDUCER |
| 188 | 1 | U.S. 5HP GEARHEAD MOTOR |
| 189 | 1 | 3HP MOTOR W/FALK 45 RPM REDUCER |
| 190 | 1 | SM CYCLO 11:1 RATIO REDUCER (SPARE DEBARKER FEED ROLL DRIVE) |
| 191 | 1 | G.E. PACIFIC 3HP/97 RPM GEARHEAD MOTOR |
| 192 | 1 | 5HP MOTOR W/WESTERN 39.7:1 RATIO REDUCER |
| 193 | 1 | ALLIS CHALMERS 200HP/1775 RPM MOTOR |
| 194 | 1 | ALLIS CHALMERS 50HP/1160 RPM MOTOR |
| 195 | 1 | LINCOLN 75HP/1775 RPM MOTOR |
| 196 | 1 | CONTINENTAL 25HP/1760 RPM MOTOR |
| 197 | 1 | U.S. 10HP/1200 RPM MOTOR |
| 198 | 1 | TOSHIBA 20HP/1755 RPM MOTOR |
| 199 | 1 | HYUNDAI 15HP/1770 RPM MOTOR |
| 200 | 1 | 10HP/1200 RPM MOTOR |
| 201 | 1 | TOSHIBA 20HP/1755 RPM MOTOR |
| 202 | 1 | TOSHIBA 20HP/1160 RPM MOTOR |
| 203 | 1 | BROOK 15HP/1720 RPM MOTOR |
| 204 | 1 | LOT, (2) ASSORTED MOTORS |
| 205 | 1 | LOT, SKK GEARBOX CASES |
| 206 | 1 | LOT, ROLLING STOCK PARTS |
| 207A | 1 | PARTIAL LOADER FORK |
| 207B | 1 | LOT, GRAPPLE PARTS |
| 208 | 1 | LOT, (2) 10.00-20 TIRES |
| 209 | 1 | LOT, PICK UP & CAR TIRES (3 PALLETS) |
| 210 | 1 | LOT, EQUIPMENT TIRES BY SHOP |
| 211 | 1 | LOT, EQUIPMENT CYLINDERS (2 PALLETS) |
| 212 | 1 | LOT, H78 ROOFTOP CHAIN (4 PALLETS) |
| 213 | 1 | LOT, HULTDINS DELIMBER HEAD W/BAR CHAIN CUT-OFF SAW (2 PALLETS) |
| 215 | 1 | 15HP HYDRAULIC UNIT |
| 216 | 1 | 10HP HYDRAULIC UNIT |
| 217 | 1 | HOE SAW GUIDE SHAPER |
| 218 | 1 | HOE SAW GUIDE SHAPER |
| 219 | 1 | JET 2-TON ELECTRIC CHAIN HOIST W/TROLLY, 1 PHASE |
| 220 | 1 | LANDA GAS FIRED PRESSURE WASHER |
| 221 | 1 | REDDYHEATER MULTI-FUEL SPACE HEATER |
| 222 | 1 | TITAN FLOOR JACK |
| 223 | 1 | HUSQVARNA 394XP CHAIN SAW |
| 224 | 1 | HUSQVARNA 2100 CHAIN SAW |
| 225 | 1 | JONSERED CHAIN SAW |
| 226 | 1 | NAPA BATTERY CHARGER |
| 227 | 1 | LINCOLN AC225/DC210 -6 GAS FIRED WELDER/GENERATOR |
| 228 | 1 | MILLER SRH404 DC ARC WELDER, 3 PHASE |
| 229 | 1 | 12-TON HYDRAULIC ADJUSTABLE SHOP PRESS |
| 230 | 1 | DAYTON 3Z326 VARI-SPEED DRILL PRESS |
| 231 | 1 | SEARS 3/4HP DOUBLE END GRINDER |
| 232 | 1 | FOREMOST 7"X12" HORIZONTAL METAL CUTTING BAND SAW |
| 233 | 1 | SAFETY-KLEEN MOTORIZED PARTS WASH TANK |
| 234 | 1 | LOT, ASSORTED ROLLING STOCK PARTS |
| 235 | 1 | LOT, MISCELLANEOUS W/WOOD SHELF |
| 236 | 1 | LOT, ASSORTED CYLINDERS |
| 238 | 1 | MILWAUKEE RIGHT ANGLE GRINDER |
| 239 | 1 | SKIL CIRCULAR SAW |
| 240 | 1 | BLACK & DECKER VARI-SPEED HAND DRILL |
| 241 | 1 | C.P. 3/4" DRIVE PNEUMATIC IMPACT WRENCH |
| 242 | 1 | INGERSOLL-RAND 3/4" DRIVE PNEUMATIC IMPACT WRENCH |
| 243 | 1 | INGERSOLL-RAND 1/2" DRIVE PNEUMATIC IMPACT WRENCH |
| 244 | 1 | MASTER JIG SAW |
| 245 | 1 | LOT, C-CLAMPS |
| 246 | 1 | 2-ARM PULLER |
| 247 | 1 | LOT, LARGER COMBO WRENCHES |
| 248 | 1 | LOT, SMALLER COMBO WRENCHES |
| 249 | 1 | LOT, IMPACT SOCKETS W/RATCHET |
| 250 | 1 | LOT, RIDGID PIPE CUTTER & REAMER |
| 251 | 1 | LOT, PIPE WRENCHES |
| 252 | 1 | PROTO 20" ADJUSTABLE WRENCH |
| 253 | 1 | BENCH VISE |
| 254 | 1 | LOT, WELDING WIRE |
| 255 | 1 | LOT, ASSORTED TOOLS IN BOX & ON WALL |
| 256 | 1 | BOTTLE CART |
| 257 | 1 | PNEUMATIC LUBE UNIT W/CART |
| 258 | 1 | LOT, TAPER LOCKS (UPSTAIRS) |
| 259 | 1 | LOT, ASSORTED ELECTRIC MOTORS |
| 260 | 1 | DAYTON ELECTRIC WINCH |
| 261 | 1 | DAYTON ELECTRIC WINCH |
| 262 | 1 | LOT, ASSORTED ELECTRIC BOXES |
| 263 | 1 | LOT, MISCELLANEOUS |
