|
9AM - TUESDAY - AUGUST 3
25500 N Hwy 101, Willits, CA
9AM - WEDNESDAY - AUGUST 4
32600 Holquist Lane, Fort Bragg, CA
Past Auction - held in 2004
Web Catalogs: Day 1 | Day 2
PDF Catalogs: Day 1 | Day 2
Advance Bid Center
|
WILLITS
DEBARKER
|
- SALEM Mark II 27" 5-arm ring debarker, US 75 hp ring drive, GE 75 hp MG set, US 40 hp DC feed drive, air ring, hold downs, feed thru alligator chain, 58' infeed hourglass rollcase, 50' outfeed hourglass rollcase, 50' box chain cleanout conveyor, drives, controls, cab
|
|
CUTOFF SAW
|
- 72" insert tooth whole log cutoff saw, (3) STROM cradles, cylinder, US 50 hp/1170 rpm drive, 60' 2-strand H124 infeed log haul w/flites, (2) sets 30" hourglass rolls, drives, controls, cab
|
|
HEADRIG BANDMILL
|
- 6' RH headrig bandmill, GE 150 hp/705 rpm, 1-3/4" top wheel, mechanical strain, in & outfeed rolls, feed thru belt, drives, LINCOLN lube, controls, cab
|
|
CARRIAGE, DRIVE, LOG TURNER
|
- IRVINGTON MOORE Log Boss 42" 2-knee Temposonic positioned carriage. airdogs, tongs, flippers, (4) trucks, pantograph, rail, bumpers, hydraulic tensioner, 7.5, 25 hp hydraulic units
- TYRONE BERRY SMA 260 hydraulic carriage drive, 200 hp
- CORLEY hydraulic log turner, 25 hp hydraulic unit
|
|
EDGER
|
- UKIAH 8'x60" SBA gang edger, 2-saw setworks, TECO 400 hp/1770 rpm arbor drive, DC feed drive, 25 hp MG set, (3) lasers, 10' infeed rollcase, outfeed gravity rolls, 5 & 25 hp hydraulic units, controls, cab, electrics
|
|
RESAW, PRECISION END TRIM SAW
|
- 5' horizontal band resaw, TOSHIBA 100 hp/1775 rpm arbor drive, 40:1 strain ratio, powered in & outfeed rolls, feed thru chains, controls, electrics
- (2) 8' precision end trim saws, (3) 24" saws, 10 hp ea, electrics
|
|
STACKER SYSTEM, TILT HOIST
|
- GILLIHAN 6'-8' lumber stacking system, 1"-2" thickness, 3"-6" width, 6'-8' length, 4'x4' package capacities w/2-arm 8' mechanical tilt hoist, 55" arms, sticker belt, 16' 4-strand transfer, even end chain, 4-arm lowering hoist, drives, electrics, catwalk, 20'x40' shed roof
- 3-arm 8' mechanical tilt hoist w/motor to reducer
|
|
CHIP BINS
|
- 42.5 unit hydraulic chip bin, 15 hp, 4' dia cyclone
- 8'x10'x16' surge bin w/twin augers60" blower, 75 hp
- High & low pressure blowpipe
|
|
CHIPPER, FEEDERS, SHAKER
|
- BLACK CLAWSON 66" 8-knife chipper w/key knife conversion, horizontal infeed, bottom discharge, 200 hp/600 rpm, drive, ASEA size 6 reduced voltage starter
- RADER 20"x20" chip feeder w/silencer, motor to SM CYCLO
- CLARK 20"x20" chip feeder w/silencer, motor to FALK
- CM&E 4'x8' 2-deck chip screen
|
|
COMPRESSORS
|
- QNW 740 150 hp rotary screw air compressor, 200 psi, MODINE heat exchanger, 78,894 hrs, s/n: 760213
- QNW 650H 150 hp rotary screw air compressor, 200 psi, MODINE heat exchanger, 86,866 hrs, s/n: 740203
|
|
FILING & GRINDING ROOM
|
- (2) ARMSTRONG #6 sharpeners
- ARMSTRONG #4, #5 stretcher rolls, s/n's: 6346, 2756
- (2) ARMSTRONG 3-10C stretcher rolls, s/n's: 12229, 8167
- (2) ARMSTRONG #25 sharpeners, s/n's: 13378, 7183
- NEWMAN G280 tub grinder, s/n: 280243
- Assortment of spare band & round saws, 20" anvil, more
|
|
SCALE, TRAILER LOADER
|
- MURPHY CARDINAL 60 ton, 10'x70' truck scales w/CARDINAL 738 100,000 lb x 20 lb DRO, s/n: 860672
- 12,000 lb trailer loader w/electrics
|
|
CONVEYORS, TRANSFERS, ROLLCASES
|
- MILLPOWER 40"x24' vibratory conveyor w/5' fiberglass tub, MDI L240 metal detector
- 64' 5-strand 4" rolltop greenchain
- 58' 5-strand H124 infeed log deck, S drive, TOSHIBA 20 hp, SM CYCLO 59 rpm reducer
- 60' 4-strand H78 transfer
- 32' 3-strand H78 transfer
- 24' 4-strand H78 transfer, TOSHIBA 5 hp, SM CYCLO 16 rpm reducer
- 24' 3-strand H78 transfer, SM CYCLO reducer
- 21' 8-strand H124 infeed log transfer
- 21' 4-strand 2-section H78 transfer, EURODRIVE 5hp
- 16' 6-strand H124 log transfer
- 16' 3-strand H78B transfer
- 14' 3-strand H78 transfer
- 12' 3-strand H124 re-entry log deck, S drive
- 11' 6-strand H78 transfer, S drive
- 11' 3-strand H78B transfer
- 8' 4-strand H78B transfer
- 7' 4-strand H78B lumber landing table
- 4'x5' slat chain transfer
- 4' 4-strand H78B lumber landing table
- 3-arm log stop and loader
|
|
ELECTRICAL
|
- ALLEN BRADLEY Centerline 5-section MCC w/(25) switches, size 5 starter
- 3000 amp power breaker
- ASEA size 6 reduced voltage starter
- starters
- disconnects
- lighting panels
- transformers
- mill lighting
|
|
BUILDINGS
|
- 40'x120' all steel 2-story mill building, catwalk, stairs, wood interior buildings, lights, air & water lines
- 30'x60'x15' high metal clad wood frame shop building
- 14'x24'x15' high all steel fuel building
|
|
MISCELLANEOUS MILL EQUIPMENT
|
- Large assortment of mill equipment including diesel & gasoline fuel tanks w/pumps, fire extinguishers, cameras, monitors, lasers, log bunks, hardware, sprockets, hoses, pipe & hydraulic fittings, belts, welding equipment, air receivers, ANSUL fire suppression system, banding carts, shop press, drill presses, double end grinders, headrig & hog parts, chain, much more
|
|
ROLLING STOCK
|
- 1991 CAT 231 heel boom log loader, CAT 3208 diesel, PIERCE boom, enclosed cab, s/n: 1NK254
- CAT 235B heel boom log loader, CAT 3306 diesel, PIERCE boom, enclosed cab, s/n: 8Z35853
- 1995 CAT 950F log loader, CAT 3116 diesel, hydraulic pump, MEDFORD log forks, enclosed cab, 11,700 hrs(300 hrs on engine), s/n: 58K1560
- CAT 966D log loader, CAT 3306 diesel, MEDFORD log forks, enclosed cab, 17,900 hrs, s/n: 94X0154
- 1983 CAT V80D 8000 lb forklift, propane, 158" 2-stage mast, sideshift, s/n: 40X1843
- CLARK 40B 4000 lb forklift, 106" 2-stage mast, s/n: CY40B27981568
- 1985 FMC/WAYNE sweeper, DETROIT diesel, hydrostatic drive
|
FORT BRAGG
DEBARKER
|
- SALEM Mark II 27" 5-arm ring debarker, air ring, BALDOR Super E 75 hp/1170 rpm, MOTOTRONICS XL Series soft start, hold downs, infeed pinch & feed rolls, 10 hp hydraulic unit, 3'x8' air receiver, spare LINDSEY tool arms, 70' infeed box chain log haul, 60' outfeed box chain log haul, cab, controls, cameras, monitors, spares, s/n: 7141321
|
|
CUTOFF SAW
|
- Twin 84" insert tooth whole log cutoff saw, 125 hp, (3) clamps, (4) stop gates, feed thru hourglass rolls, 52' infeed box chain log haul, 15 hp, SM CYCLO reducer, BALDOR solid state starter, EUROTHERM AC600+ Series integrator, B&T 55 hp hydraulic unit, GE 8000 line 5-section MCC w/(18) switches, cab, controls, cameras, monitors
|
|
HEAD RIG BANDMILL
|
- KLAMATH D 7' LH double cut headrig bandmill, GE 200 hp/585 rpm, 1-1/4" top wheel, mechanical strain, in & outfeed rollcases, 1991 B&T 50 hp hydraulic unit, 34 gpm, 1500 psi, 1991 LCI scan curtain, (33) eyes, blower, BALDOR frequency drive computer, cab, controls cameras, monitors, spares
|
|
CARRIAGE, DRIVE, LOG TURNER
|
- 1990 KLAMATH TFD-H 42" 2-knee Temposonic positioned carriage, airdogs, tongs, flippers, (3) trucks, pantograph, rail, bumper, s/n: 575
- TYRONE BERRY SMA 230 hydraulic carriage drive, 125 hp, 1500 psi, s/n: A1114
- SALEM hydraulic log turner, 25 hp hydraulic unit
|
|
SCRAGG SAW
|
- Custom built 42" circular saw scragg, splined bottom arbor, TOSHIBA 300 hp/1185 rpm, 25 hp log carriage drive, feed thru rolls, 24"x12' outfeed belt, outfeed rollcase, 30' 2-strand H124 infeed deck, 6' 2-strand unscrambler, 12' 2-strand infeed transfer, 2-arm log stop & loader, spares
|
|
EDGER
|
- UKIAH 6"x54" gang edger, splined top arbor, UKIAH saw glide system, TOSHIBA 300 hp/1775 rpm arbor drive, RELIANCE 20 hp/1150 rpm feed drive, FALK square box 190 rpm reducer, press rolls, (4) lasers, 16' split roll infeed rollcase, dual 8' linebars, 128' outfeed rollcase, EUROTHERM 590 digital drive, AB SLC 5/03 CPU, 7.5 hp hydraulic unit, controls, spares
|
|
TRIMMER
|
- Custom built 10' 5-saw trimmer, 7.5 hp/1800 rpm, 24" saws, zero saw, MOTOTRONICS ABC series brakes, (4) lasers, 30' 4-section 3 & 5-strand lugged feed transfer, cam feeder, (2) BALDOR adjustable speed drives, AB SLC 5/04 CPU, (4) lasers, 36" blower, 3' dia long neck cyclone
|
|
PLANER
|
- ECKSTROM CARLSON 615 planer/matcher, 6"x15", (6) heads, (14) knives, 75 hp top & bottom, 35 hp sides, 35 hp bottom profile, MOTOTRONIC brakes top, bottom & side heads, 40 hp feed drive, 10' dual pineapple feed table, anti-stain tunnel, 30"x14' outfeed belt, profiles, jointer bars, spare heads, bearings, parts, spider, s/n: 101
|
|
PRECISION END TRIM SAWS, STACKER, BANDER
|
- 8' precision end trim saw, (2) 24" saws, 10 hp/3450 rpm, starwheel feeder, 6' 2-strand infeed transfer, even end rolls, chain, 1995 IRVINGTON MOORE 3228 double end stud printer & waxer, 30' 3-section 2-strand transfer, 8' overarm stacker, end squeeze, 2-arm lowering hoist, ACME RAPZ 54"x72" manual bander, side squeeze, 16' feed thru rollcase, 16' 2-strand outfeed trnasfer, EUROTHERM 584S drive, AB SLC, 5/03 CPU
- 10' precision end trim saw, (2) 24" saws, 10 hp/3450 rpm, starwheel feeder, 12' 2-section 3-strand infeed transfer, even end rolls & chain, 12"x16' cutoff belt, 40' 2-section 2-strand transfer, MOORE OREGON L78075 10' overend stacker, grade stamp, 900 lb capacity, (6) cycles/min, 2-arm lowering hoist, 24' outfeed rollcase, BALDOR drive, EUROTHERM AC 600+ series integrator, s/n: 100-1
- 8' 2-arm mechanical tilt hoist, 52" arms, gearhead motor
|
|
CHIP BINS, SURGE BINS, CYCLONES, FEEDER, BLOWERS, SHAKER, BARK HOG, CHIPPER
|
- (3) LSI 60-unit chip bins, 15 hp hydraulic unit
- PEERLESS 60 unit chip bin, 15 hp hydraulic unit, 8' cyclone
- (2) PEERLESS 40 unit chip bins
- PEERLESS 24 unit chip bin, 15 hp hydraulic unit
- 4'x10' surge bin w/(4) augers, motor, FALK reducer
- 4'x10' surge bin w/(2) augers, gearhead motor
- 2001 WESTERN PNEUMATICS 7164500 20"x25" feeder, LINCOLN 75 hp/1765 rpm, silencer, s/n: 164518
- 2001 WESTERN PNEUMATICS FDRW20250LC 8"x16" high pressure blower, 5 hp/1750 rpm, DODGE shaft mount reducer, s/n: FDRW1035
- 48" planer blower
- (2) 36" blowers w/3' dia long neck cyclones
- SODERHAMN KS010 10'x10' 3-deck shaker screen, s/n: 06012
- LAMB 36"x42" bark hog, RELIANCE 250 hp/1190 rpm, top feed roll, 7.5 hp/1775 rpm, SM CYCLO reducer, bottom feed roll, EURODRIVE 3 hp/44 rpm gearhead, starter, metal building, spares
- BLACK CLAWSON 78" 6-knife chipper w/key knife conversion, 150 hp/600 rpm, MOTOTRONICS brake, starter, horizontal infeed, bottom outfeed, spares, s/n: 55688
- Small & large dia blowpipe, flatbacks, more
|
|
COMPRESSOR
|
- QNW 380F 100 hp rotary screw air compressor, 200 psi, s/n: 740957
|
|
FILING & GRINDING ROOM
|
- ARMSTRONG #6 RH sharpener, s/n: 13825
- ARMSTRONG #5 stretcher roll, BALDOR drive, s/n: 3825
- ARMSTRONG 3-60C stretcher roll, s/n: 12374
- ALLIGATOR stellite tipper, s/n: PA6018
- IMW 240 guide grinder
- WRIGHT W350 auto dual super HD side grinder
- (2) ARMSTRONG 3-10 stretcher rolls
- (2) ARMSTRONG #25 sharpeners w/AB drives, s/n's: 14908, 13327
- NEWMAN G-280 tub grinder
- YATES travel bed grinder, s/n: 29944
- YATES M7 travel bed grinder
- Plus: BARNHARDT wheel grinder
- ACME hand gummer
- hoe guide grinder
- DUSTKOP dust collector
- ARMSTRONG #6 swage
- ARMSTRONG 6900 shaper
- 36", (2) 18" anvils
- spare bandmill & circular saws
- guide material
- babbit pots
- HANCHETT #2 bandsaw shear
- more
|
|
SCALE, TRAILER LOADER
|
- MURPHY CARDINAL 60 ton, 10'x70' truck scale w/DRO
- 5000 lb trailer loader
|
|
CONVEYORS, TRANSFERS
|
- MILLPOWER 36"x44' vibratory conveyor, 9' fines dropout, 5' fiberglass tub, MDI metal detector
- MILLPOWER 24"x36' vibratory conveyor, 8' fines dropout, 5' fiberglass tub, MDI metal detector
- (2) 60' 2-strand H150 transfers
- 42' 6-strand H124 transfers, S drive, 6-arm log stop
- 40' 2-strand H124 trasnfer, TOSHIBA 10 hp, SM CYCLO reducer
- (2) 28' 2-strand jack ladder transfers, 7.5 hp
- 21' 3-strand H78 transfer, gearhead motor
- 20' 8-strand H124 transfer, S drive, 30 hp, FALK reducer
- (2) 18' 2-strand H124 transfers, S drive, GE 7.5 hp
- 16' 2-strand H78 transfer, gearhead motor
- 15' 5-strand H82 unscrambler, TOSHIBA 10 hp, SM CYCLO reducer
- 12' 3-strand H78 transfer, SM CYCLO 5 hp
- 12' 2-section 3-strand H82 transfer, (2) TOSHIBA 10 hp, SM CYCLO reducer
- 10' 4-strand H78 unscrambler, BALDOR Super E 5 hp, SM CYCLO reducer, brake
- 9' 3-strand H82 transfer, TOSHIBA 10 hp, SM CYCLO reducer
- 4' 4-strand H78 lumber landing table, BALDOR 5 hp, SM CYCLO reducer
- (20+) conveyors to 220'
- (10+) belt transfers to 130'
|
|
ELECTRICAL
|
- CHALLENGER 3-section 3000 amp/450V main panel w/800 amp, (5) 1200 amp adjustable trip switches
- ALLEN BRADLEY 3-section MCC w/(12) switches, AB 150 SMC
- ALLEN BRADLEY 3-section MCC w/(22) switches
- 2-section MCC w/(7) switches, EUROTHERM 584SV starter
- ALLEN BRADLEY 2-section MCC w/(7) switches
- new BALDOR D71X SS starter
- MOTOTRONICS XL120 brake
- new GE 15kva 240x480/120x240 transformer
- (3) new GE 35 kvar capacitors
- starters to size 5
- much more
|
|
BUILDINGS
|
- 110'x228' all steel irregular shaped mill building w/interior wood buildings, lighting, air & water lines, extensions over tilt hoist, stackers
- 30'x30'x12' high all steel building
|
|
MISCELLANEOUS MILL EQUIPMENT
|
- LANDA PW100 jetspray washer
- SIOUX 160 steam cleaner
- MILLER Intelliweld 650 & Dimension 400 welders
- DAYTON 16-1/2" drill press
- double end grinders
- flammables cabinets
- ladders
- dumpsters
- fire extinguishers
- steel stock
- 4'x14', 3'x8' air receivers
- 1000 lb hydraulic log splitter
- (2) CM 1/2 ton chain hoists
- CM 1 ton chain hoist
- (2) POULAN 16" chain saws
- vises
- oxy acetylene set
- pneumatic & hand pumps
- safety harnesses
- drum heater
- lockouts
- metal cabinets
- lumber carts
- spill pallet
- drum cradles
- new chain
- sprockets
- pulleys
- cylinders
- water tank system
- key knife
- SWEED 450 scrap chopper
- conveyor trough
- new UPS backup
- new CHROMALOX heater
- lasers
- monitors
- cameras
- industrial intercom
- heaters
- relays
- timers
- mobile radios
- conduit & fittings
- motors to 300 hp
- reducers
- wire
- too much more to list
|
|
ROLLING STOCK
|
- 1995 LE TOURNEAU 4594 Letro stacker, DETROIT 60 Series diesel(rebuilt 2003), 6296 total hrs, s/n: 2003
- CAT 229 heel boom log loader CAT diesel, encolsed cab, s/n: 73V13129
- CAT 966C articulated log loader, CAT diesel, log forks, enclosed cab
- CAT 140G motor grader, CAT diesel, 12' moldboard, 8-barrel ripper, s/n: 72V04951
- CAT 12 motor grader, CAT diesel, scarifier, 12' modlboard, s/n: 8110250
- CAT D7F crawler tractor, 3306 CAT diesel, 11' straight blade, HYSTER winch, canopy, s/n: 9FN5696
- CASE 580C backhoe w/extendahoe, diesel, 6' bucket, canopy, 285 hrs, s/n: 8984498
- HYSTER H150E 15,000 lb pneumatic forklift, PERKINS diesel, monotrol trans, 182" 2-stage mast, sideshift, s/n: B7P-5160N
- HYSTER 6000 lb HRT forklift, propane, 2-stage mast, sideshift
- 1966 PETERBILT T/A dump truck, CUMMINS diesel, 6/4 trans, 98,839 miles
- FRUEHAUF 28' van trailer
- 1999 DODGE 1500 pickup
- 1995 CHEV 2500 pickup
- 1994 FORD F250XL 4x4 pickup, V8, auto, w/trailer brake, dual tanks, portable diesel tank, pump, truck box
- (2) 1994 FORD F250 pickups
|
|
TERMS & CONDITIONS
|
- 7% BUYERS PREMIUM
- PAYMENT
: Full payment must be made by no later than 4pm, Thursday, August 5 for both locations.
- A 25% deposit is required by the close of business, each auction day.
- Cash, cashiers check, Master & Visa Cards, wire transfers only. Personal or company checks accepted ONLY with bank letter of guarantee.
- Absentee bids accepted with 25% deposit
- REMOVAL: No purchase may be removed during the auction unless otherwise announced by the auctioneer. Equipment removal schedule announced on auction day.
- Announcements made by the auctioneer at the time of sale take precedence over printed matter.
- Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
- Due to safety & insurance reasons, persons under 12 not admitted.
- Washington Auctioneers License #48
- CA Bond #445652C
|
|
DRIVER DIRECTIONS
|
- WILLITS: The auction site is approximately 4 miles north of Willits on Hwy 101. The Willits location is approximately 37 miles east of the Ft Bragg location via Hwy 20.
- FT BRAGG: At the intersection of Hwy 20 and Hwy 1 in Ft Bragg drive south on Hwy 1 approximately 2.5 miles to Gibney Lane. Turn left on Gibney Lane which becomes Holquist Lane and drive approximately 2/10 mile to the auction site.
WATCH FOR AUCTION SIGNS
FOOD SERVICE AVAILABLE AT THE AUCTION SITE
|
|
LODGING WILLITS
|
| BAECHTEL CREEK INN | | 707-465-3402 |
| BEST WESTERN WILLITS INN | | 707-459-5800 |
| SUPER 8 MOTEL | | 707-459-3388 |
| HOLIDAY LODGE MOTEL | | 707-459-5361 |
|
|
LODGING FT BRAGG
|
| EMERALD DOLPHIN INN | | 1-866-964-6699 |
| BEST WESTERN VISTA MANOR LODGE | | 707-964-4776 |
| HARBOR LITE LODGE | | 707-964-0221 |
| HOLIDAY INN EXPRESS | | 707-964-1100 |
|
|
AIRPORTS & CAR RENTAL
|
- San Francisco International Airport is served by all major airlines and rental car agencies. It is approximately a 3 - 3.5 hour drive to the auction sites.
- Eureka/Arcata Airport is served by Alaska Airlines and United Airlines. Rental cars are available. It is approximately a 2.5 - 3 hour drive to the auction sites.
|
Home | About Us | Auction Schedule | Immediate Sales | Email Signup | Map | Past Auctions | Registration Form | Advanced Bid Overview | Terms & Conditions | Best of 2000-2004 Auctions
James G. Murphy Co.
Commercial / Industrial / Real Estate Auctioneers
P.O. Box 82160 - 18226 - 68th Ave. N.E.
Kenmore, Washington 98028
(425) 486-1246 or Toll Free 1-800-426-3008
Fax: (425) 483-8247
Oregon address & phone:
105 McNary Estates Dr. N
Keizer, OR 97303
phone: (503) 463-4444
fax: (503) 463-1554
Copyright©1997-2005 James G. Murphy Co.
All rights reserved worldwide
|
|
|
