Auction X Catalog

• 1994 NICHOLSON A5A-LH debarker, 22" 100 hp ring drive, reversing in/outfeed rollers, short log capable(located in Wright City, OK)
• 1981 NICHOLSON 35A2 35", 5-arm ring debarker, NEWMAN 75 hp/885 rpm ring drive, TOSHIBA 30 hp/1760 rpm feed drive, REX PLANET gear reducer, in & outfeed alligator chains w/hold downs, 20 hp hydraulic unit, lines & manifolds, cab & controls, s/n: 22930053
• CAMBIO 24", 6-arm debarker, BROOKS 75 hp/1165 rpm ring drive, WESTINGHOUSE 15 hp/1770 rpm drive, air cylinders, in & outfeed log hauls w/drive motors, cab & controls, s/n: 7857127
• CAMBIO 30" ring debarker, 75 hp, s/n: 35(located in Wright City, OK)

• Twin air actuated 110" cutoff saws, 75 hp/1760 rpm drives, hold down, feed thru hourglass rolls, cab & controls (no saws installed)
• Air actuated 72" insert tooth cutoff saw, 75 hp/1770 rpm drive, infeed log haul w/powered & non powered hourglass roll, cab & controls

• RAMEY HA127 hydraulic operated rail mounted knuckleboom log loader, swivel grapple, DETROIT diesel

• 1990 DURAND-RAUTE 104" spindleless lathe, (2) 50 hp dc feed roll drives, TEMPOSONIC & hydraulic positioned cylinders & rolls, jack ladder log singulator, 410 hp hydraulic unit, CARRIER liquid chiller, controls & electrics, s/n: 90-6000
• 1990 DURAND-RAUTE round-up lathe, (2) 30 hp dc motors, TEMPOSONIC & hydraulic positioned cylinders & rails, jack ladder log singulator w/(2) end trim saws & motors, 245 hp hydraulic unit, CARRIER liquid chiller, controls & electrics, s/n: 90-5900
• DURAND-RAUTE rotary clipper w/25 hp hydraulic unit, (no controls, infeed or outfeed)
• Disassembled tray system & stacker, infeed

• COE 249D 8' veneer lathe w/dual retractable chucks,COE 765 lathe charger, CFS back up roll conversion, 10 hp hydraulic unit, controls, booth
• TAHKA 10'x15' step feeder
• 100', 3-deck veneer tray system (no drive motor), infeed tipple, trash return transfer, trash gate, partial infeed to stacker
• DURAND-RAUTE rotary clipper, 25 hp hydraulic unit, incomplete controls, infeed transfer (no outfeed transfer), s/n: 89-5227

• (3) WILLIAMS WHITE 30-opening hot presses, 4'x8', hydraulic operated presses, feeder, gravity rolls, outfeed gravity rolls, 100 hp hydraulic units, controls, electrics
• WILLIAMS WHITE hot press, 24-opening, 572 ton, 106"x54", s/n: 3467(located in Philadelphia, MS)
• 1994 SPAR-TEK hot press loader/unloader(located in Philadelphia, MS)
• (3) SUPERIOR 4'x8', 4-ram pre-presses, 40 hp hydraulic units, infeed rollcase/transfer, outfeed rolls, crossover transfers
• GLOBE 4'x8' pre-press w/in & outfeed(located in Philadelphia, MS)
• SUPERIOR 4'x8' pre-press w/in & outfeed(located in Philadelphia, MS)

• GLOBE tongue & groove machine, 20 hp, 1775 rpm arbor motors, feed rolls, infeed transfer, vacuum transfer, infeed rollcase, outfeed belt transfer, belt sort transfer, (3) lumber lowering stackers, outfeed rollcase, gravity rolls, outfeed rollcase, 15 hp hydraulic unit
• GLOBE skinner saw line w/(2) infeed transfers, vacuum transfer, powered feed rolls & hold down rolls, adjustable double end trim saws, belt transfer, double end trim saw w/feed thru chains & end even roll, belt transfer, UPC code applicator, (3) lumber lowering stackers, powered outfeed rollcases, ACME strapping station, outfeed transfer w/gravity rolls, squaring station, 18"x40' clean out belt, 6"x14' clean out belt, 10 hp hydraulic unit, motors, PLC controlled electrics, control cab
• LP specialty siding saw line w/scissor lift infeed rollcase, vacuum transfer, infeed rolls, chain type rough length saw, 30 hp, (2) horizontal arbor grooving saws, 3 & 25 hp, (2) vertical arbor coping saws, 5 hp, outfeed belt transfer rollcase, 7-arm paddle type board turner, belt transfers, (4) lumber lowering stackers, outfeed chain transfer & gravity rolls, drives, hydraulic unit

• (2) 84" insert tooth circular core saws w/feed thru transfers, motors, electrics
• Slasher deck saw system w/18'x35', 12-strand slasher deck ,(5) 60" insert tooth slasher, slasher saws, (5) RELIANCE 50 hp/1185 rpm, 24', 3-strand infeed transfer w/motor & kicker, 24"x30' outfeed belt conveyor w/motor, controls

• JEFFREY 48"x60" hammer hog, TOSHIBA 60 hp/1185 rpm
• LP 24"x24" mini hog, 50 hp
• (2) BELOIT PRECISION 75, 75", 6-knife chippers, horizontal infeed, bottom discharge, RELIANCE 250 hp/1185 rpm(1 without motor or infeed chute)
• (2) ACROWOOD 76", 8-knife chippers, horizontal infeed, bottom discharge, w/chip breaker & drive, RELIANCE 200 hp/1185 rpm
• PRECISION 66-17 66", 6-knife chipper, horizontal infeed, bottom discharge, RELIANCE 250 hp/1185 rpm, s/n: C1598
• ACROWOOD 60", 12-knife disk chipper, horizontal feed, bottom discharge(located in Wright City, OK)
• BRADSON lily pad chipper, TOSHIBA 200 hp/1180 rpm
• LP 20"x20" rechipper, LINCOLN 75 hp/1770 rpm
• PNEUMATIC SYSTEMS INC. 24"x30" chip feeder, TOSHIBA 10 hp/1745 rpm, FALK 24:94 to 1 quad drive reducer
• 1995 RADER 20x20 chip feeder, 7.5 hp, s/n: 4850(located in Philadelphia, MS)
• Twin screw feeder, 20"x137" rotor, top feed, bottom discharge, 10 hp(located in Philadelphia, MS)
• BLACK CLAWSON 6'x12', 3-deck chip screen w/motor
• 3'x15', 3-deck chip screen w/motor
• SUTORBILT 5100 Series 14"x37" rotary lobe high pressure blower, TOSHIBA 200 hp/890 rpm
• NEW YORK BOILER 737RTS low pressure blower, TOSHIBA 250 hp/1185 rpm
• 72" low pressure blower, US 200 hp/1775 rpm
• 72" low pressure blower, TECO 200 hp/1775 rpm

• (2) Approximately 40-unit bolt together hydraulic operated chip bins w/distribution auger, 10 hp hydraulic unit
• (2) Approximately 24-unit bolt together hydraulic operated chip bins w/distribution auger
• 23'w x31'l x34'h live bottom surge bin w/(1) 4-auger screw, (2) 6-auger screws, TOSHIBA 10 hp/1750, SM CYCLO 289 rpm reducers
• MAC 13'w x32'l x21'h live bottom surge bin w/chain bottom conveyor, rotary airlock
• 1995 MAC 14411CF756 baghouse w/rotary air lock, SUTORBILT blower w/motor, s/n: 95-F11CF-03-08
• 4'-8', 10' dia. longneck cyclones
• 2-station wig wag chip car loader w/diverters & (2) rail car winches
• (2) WESTERN PNEUMATIC in line flow units
• Large quantity of low & high pressure blow pipe to 60" dia., diverters, hard backs

• 1970 ERIE CITY BOILER WORKS 110,000 lbs/hr wood & natural gas fired boiler, 300 psi, $1,200,000 retrofit in 2000 to include COEN 215DAZ-18 single sander dust/natural gas fired burner, CO-VENT 60" ovefire air fan, OPTIM 150 hp/1750 rpm, CO-VENT 30" distribution air fan, OPTIM 25 hp/3485 rpm, grate steam cleaning system w/bed, ASN drag chain system, EFFOX multi-blade, wafer dampers, EFFOX expansion joints, WASHBURN-GARFIELD valves throughout, new tiles & skin on back half, existing equipment includes 4-auger feed screws w/hydraulics, de-aeration tank, feed water pumps, controls & electrics, ZURN Type MTSA-119-9CYI-XD-T fly ash recovery system, blowers, TOSHIBA 500 hp,G.E. 125 hp, s/n: 970648-901 (*sold subject to owners acceptance)
• ERIE CITY 80,000 lb/hr wood fired boiler at 300 psi, auger screw infeed fuel system w/hydraulic unit, 60' infeed fuel conveyor, feed water pumps, controls & electrics, ZURN fly ash recovery system

• Core to timber/stud landscape timber machine, 50 hp, (6) powered feed rolls, 12' infeed chain transfer
• 8', 2 arm hydraulic operated lumber hoist , 7.5 hp hydraulic unit

• (2) CUTLER HAMMER Easy Start ES120 solid state reduced voltage starters w/1200 amp adjustable trip breaker
• (4) WESTINGHOUSE 4200 amp interrupting switchboards
• WESTINGHOUSE 1200 amp interrupting switchboard
• (5) WESTINGHOUSE 2000 amp switchboards
• G.E. 2000 amp av line switchboard
• CUTLER HAMMER MP200 1600 amp switchboard w/1600 amp adjustable trip breaker
• CUTLER HAMMER MP200 1200 amp switchboard w/(2) 1200 amp adjustable trip breakers
• CUTLER HAMMER 1000 & 1200 amp panel boards w/adjustable trip breakers
• ALLEN BRADLEY 7 section MCC w/(24) switches
• (2) G.E. 6 section MCC's
• CUTLER HAMMER Freedom 2100 MCC
• (90+) sections of CUTLER HAMMER Unitrol MCC
• TOSHIBA ESP130 transistor inverter
• TOSHIBA Tosvert 130G1 & G2 transistor inverters
• Large quantity of transformers to 660 kva, starters to size 7, disconnects, capacitors, new & used cable tray, new & used wire, support electrical supplies, wire and conduit

• Chain log decks to 60', chain log hauls to 75', 24"x18' vibratory conveyor w/motor & MDI metal detector, 18"x18' vibratory conveyor w/motor & MDI metal detector, chain conveyors to 150', troughing roll belt conveyors to 185', belt conveyors to 100', assorted chain & belt, chain transfers to 120', belt transfers to 70', rollcases to 40', motors to 600 hp(large quantity of TOSHIBA), reducers(large quantity of SM CYCLO)

• REFORM 31 traveling bed knife grinder
• COE 431 traveling bed knife grinder
• ATKINSON DYNAMICS mill intercoms
• mill yard lighting
• ACME PST-3812 plastic bander
• 1993 LIDE air receiver tank,12' dia. x 25' high
• air conditioning equipment
• water, glue & chemical mix tanks
• ERIEZ N4-50C41 magnet
• (4) AMEREX nitrogen charged roll-around extinghers
• personnel fans
• 4' dia. x 16' high air receiver
• STANLEY bending chopper
• SSC 4'x8' panel saw
• BLACK BROS 4' glue spreader
• banding & clips
• concrete steam vats
• veneer carts
• chain
• sprockets
• cylinders
• rolls
• belting
• nuts & bolts
• lockers,
• racks
• water coolers
• air line, small buildings
• HERCULES Ajax HL300 21"x120" engine lathe, s/n:146804034
• CINCINNATI No. 4 vertical mill w/16"x80" T-slot table, s/n: 2A4V3H-4
• ROCKWELL 900-300 hardness tester
• swing arm jib booms
• (2) LINCOLN SA-300 dc welders
• (4) LINCOLN SA-200 dc welders
• AIRCO 300 amp de welder
• 50 hp material handling fan
• Numerous glue & chemical mix tanks
• mixers
• scales
• pumps
• huge quantity of piping & valves
• much more!

• LORAIN 15 ton crane, DETROIT diesel, s/n: 36414
• BARKO 450 hydraulic operated, self propelled log loader w/carrier, DETROIT 6V53 diesel engines, down riggers, new tires, s/n: 8081
• SULLAIR 750 DP3 trailer mounted portable air compressor, 200 psi, DETROIT diesel

• LETOURNEAU 2592 log stacker, DETROIT diesel engine, air conditioned cab, 30-33 tires, s/n: 2592-1049
• CAT 920 rubber tire loader, CAT diesel w/approximately 3 mo. on rebuild, G.P. bucket, cab, 15.5 x 25 tires
• GALION 150A hydraulic operated crane, DETROIT 453 diesel,4 section, 60' power boom, down riggers, s/n: H128388
• GROVE MZ66 zoom manlift, DEUTZ diesel, 400 lb basket, 3-stage boom, s/n: 0810339
• HYSTER H300B 30,000 lb pneumatic forklift, DETROIT 453 diesel, power shift trans, 212" 2 stage mast, side shift, s/n: B19P-1990D
• HYSTER 225 22,500 dual pneumatic forklift, DETROIT 453 diesel, 2-stage mast,spreader fork attachment for USB stacks
• HYSTER H80XL2 8,000 lb pneumatic forklift, GM 6 cyl, Monotrol trans, 2-stage mast, side shift, s/n: G005D03629R
• HYSTER H70ECB5 7,000 lb HRT forklift, 6 cyl propane, Monotrol trans, 2-stage low profile mast, s/n: C004D09038H
• CHEV S/A dump truck, DETROIT 453 diesel engine, manual trans, dual wheel

• 10% BUYERS PREMIUM
• PAYMENT: Full payment must be made by no later than 4pm,Friday, June 22.
• A 25% deposit is required by the close of business, auction day.
• Cash, cashiers check, Master & Visa Cards only. Personal or company checks accepted ONLY with bank letter of guarantee.
• Absentee bids accepted with 25% deposit
• REMOVAL:Equipment removal schedule announced on auction day. Safety orientation on equipment removal required.
• Announcements made by the auctioneer at the time of sale take precedence over printed matter.
• Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
• Due to safety & insurance reasons, persons under 12 not admitted.
• TOMMY ASSITER, TEXAS AUCTIONEERS LICENSE 6104
• Washington Auctioneers License #48
  
  

• Bush Intercontinental & Hobby International Airports are served by all major airlines & rental car agencies. Huntsville Municipal 5000' runway. Phone 936-295-8136
  
  

  HOLIDAY INN EXPRESS		936-293-8800
  LA QUINTA		936-295-6454
  COMFORT INN		936-438-8400
  BEST WESTERN		936-295-9151

• AUCTION LOCATION: The auction is to be conducted at the Walker County Fairgrounds in Huntsville, TX: From Hwy 45 take exit #103 and drive north approximately 13 miles to exit#116/Hwy 30 West. Drive west approximately 3.5 miles to the auction site.
• LP PLYWOOD, NEW WAVERLY: From Houston drive north on Hwy 45 approximately 55 miles to Waverly/Hwy 150(exit#103). Drive east approximately 8/10 mile to Hwy 75 North. Drive north approximately 2.3 miles to Farm Road 2793. Drive east approximately 9/10 mile to the mill.
• LP PLYWOOD, CORRIGAN: From LP New Waverly take Hwy 75 North and drive north approximately 2.3 miles to Farm Road 2296/Phelps. Drive east approximately 6.7 miles to Hwy 190 East. Drive east approximately 37 miles to Livingston, TX. Take Hwy 59 North approximately 21 miles to Corrigan, TX. Drive north approximately 1.1 miles to International Paper Plant Road. Turn west, drive approximately 1.1 miles and turn left just before International Paper Gate.