|
ENTERPRISE LUMBER COMPANY
MAY 15, 16, 17
9AM EACH DAY
ARLINGTON & OSO, WA
Past Auction - held in 2001
|
DAY 1 ARLINGTON SMALL LOG SAWMILL
DEBARKERS
|
- 1996 NICHOLSON A5A 27" 12-roll, air seal tandem ring counter rotating ring debarker w/ring pull out, (2) 150 hp ring drive motors, manual or remote controlled electrics, s/n: 6644
- MORBARK debarker w/14" 100 hp debarking head, 20" hydraulic driven log turning spike rolls, hydraulic support unit, control cab
|
|
LOG CUT OFF SAWS/PEDESTAL LOG LOADERS
|
- 84" swing arm insert tooth linear positioning log cut off circular saw, 100 hp drive, log clamp, 50' H132 infeed log haul, 25 hp d/c drive, 30' H110 outfeed log haul w/(7) log length stops, electric eyes, 25 hp d/c drive
- 4-1/2' bar chain log cut off saw, 20 hp drive, 7-1/2 hp hydraulic unit, log cradle, 25' outfeed log haul w/(6) log length stops
- RAMEY pedestal mounted hydraulic log loader, grapple, 50 hp hydraulic unit
- (2) PRENTICE pedestal mount hydraulic log loaders
|
|
PRIMARY LOG BREAK DOWN SYSTEMS
|
- Quad sharp chain w/(4) SALEM 5' linear positioning bandmills, (4) 100 hp motors, linear positioning saw guides, LAND EAST L&R hand linear positioning pre-slabbers, PAC knife conversion, 150 hp drives, feed thru COE sharp chain, 6'x24" lumber take away belts, hydraulic support unit
- KOCKUMS double length log infeed w/lift & side shift log linear positioning, KOCKUMS opposed spike roll log rotator, new V-guide cradle chain up grade, APPLIED SCANNING (COE) perfect shape whole log optimization scanning (TSO), NANOOSE/ PERCEPTRON whole log true shape optimizer, PORTER X-Y back up scanner, computers, electrics, hydraulics, ALLEN BRADLEY PLC controlled, QB interface to linear positioning
- MORBARK 20'x36" 4-knee linear positioning 6-truck log carriage, INOVEC 5PC setworks, rail, bumpers, TYRONE BERRY SMA240 hydraulic carriage drive w/100 hp hydraulic pump, cable, spools
- FILER & STOWELL 6' right hand mechanical strain head rig bandmill, G.E. 200 hp/700 rpm slip ring drive motor
|
|
RESAWS
|
- SALEM 6' R.H. mechanical strain line bar resaw w/100 hp motor, linear positioning line bar, pinch rolls, INOVEC 5PC setworks, infeed rollcase, hydraulic unit
|
|
CANT OPTIMIZER LINE
|
- CM&E 34 L&R hand 8-knife linear positioning slabbers, 150 hp motors w/infeed thru cant chain transfer & pneumatic hold down rolls, hydraulic support unit
- SCHURMAN cant optimizer infeed table w/cant linear positioning, lasers, hydraulic support unit
- PERCEPTRON/NANOOSE cant optimizer real shape scanner w/pass thru rollcase, computers, electrics
|
|
OPTIMIZED BOARD EDGER LINE
|
- SCHURMAN 4TA36 4"x36" cap. splined top arbor board edger w/(2) linear positioning saws, 100 hp arbor motor, hydraulic support unit, saw mist system
- CM&E #34 L&R hand linear positioning pre-slabbers, 125 hp
- 24' center chain edger feed table w/hold downs, lumber centering cylinders
|
|
SCANNER
|
- 1987 APPLIED THEORY MLS20SSEL optimizing board scanner w/pass thru 81X lugged chain transfer, end evening rollcase, 6-board linear positioning hook cylinders, hydraulic support, controls, electrics, spare CEL COM lasers, s/n: 545
- SALEM 48"x6" bottom splined arbor combo edger w/(4) linear positioning saws, 200 hp arbor motor, INOVEC 5PC setworks, lasers, hydraulic unit, in & outfeed rollcase
|
|
TRIMMERS
|
- 1990 NEWNES TA26RH46 26'x4" cap. R.H. line shaft trimmer, 100 hp line shaft drive, (2) minus fences, 18" shifting cap. 14' 13-strand feed thru transfer, 10' knurled end evening rollcase, s/n: 8987711 (Mfg. 12/89, in use approximately 3 years)
- 1990 NEWNES 26' laser optimizing board scanner w/plan view & cross section laser scanning, feed thru lug chain transfer, end evening rollcase, lug loader, computer, s/n: T89106
- POWELL 22'x6" cut, 30' pass R.H. air lift line shaft trimmer, (2) 40 hp line shaft motors, 12-strand feed thru lugged chain transfer, end evening rollcase, minus fence, PLC controlled
|
|
CHIPPERS/CHIP SCREENS/CHIP BINS
|
- SODERHAMN 58, 58" 8-knife horizontal feed, top discharge chipper, 200 hp, w/PAC knife conversion, s/n: 059-249
- SODERHAMN 58" 6-knife horizontal feed, top discharge chipper, 200 hp
- BMW 6'x12' 3 deck chip shaker screen
- PEERLESS 15-unit hydraulic chip bin
- CAROTHERS 30-unit hydraulic chip bin
|
|
AIR COMPRESSORS/AIR DRYERS
|
- QUINCY QNW1000B air cooled rotary screw compressor, 200 hp, s/n: 87058
- 1998 QUINCY QNW753-D air cooled rotary screw compressor, 200 hp, s/n: 980147C
- QUINCY QNW500-B2 air cooled rotary screw compressor, 100 hp, s/n: 860147
- 1999 HANKISON DEP Series 2,100 cfm blower purge desiccant air dryer,
- VAN AIR HB500 air dryer
- AIRTEK TW100 air dryer
|
|
FILING & GRINDING ROOMS
|
- ISELI MECOMAT 391 auto leveler, s/n: 6123
- ISELI SAA Stellite tipper, s/n: 707008
- (2) WRIGHT W1801 side tooth grinders, s/n's: 1825, 1822
- (2) ARMSTRONG #4 L.H. bandsaw sharpeners, s/n's: 13110, 9962
- (2) ARMSTRONG #4 R.H. bandsaw sharpeners, s/n's: 14892, 4744
- (2) ARMSTRONG #2 bandsaw sharpeners, s/n's:L.H.-14847, R.H.-13006
- (2) ARMSTRONG #4 bandsaw stretcher rolls w/leveling blocks
- ARMSTRONG #2 bandsaw stretcher roll w/leveling block, s/n: 13182
- (3) assorted saw guide shapers
- ALLIGATOR dual side bandsaw grinder
- ARMSTRONG 3-10C circular saw stretcher roll, s/n: 15893
- WRIGHT W-1700 circular saw profile grinder
- WRIGHT W-150HD-B circular saw grinder
- CM&E #69 bent knife grinder w/hydraulics, s/n:2341
- HANCHETT Challenger DN60 straight knife grinder, s/n: 6136
- BELL F500 circular saw top & face grinder, s/n: 76C48
- ARMSTRONG #25 circular saw sharpener, s/n: 10063
- ARMSTRONG #16 circular saw sharpener, s/n: 9491
- ARMSTRONG tension gauge grinder
- SALEM, SHURMAN edger guide babbit milling machines
- Plus: (3) assorted post grinders, BARNHART wheel grinder, DUSTKOP dust collectors, anvils, band & circular saws, babbit pots, much more!
|
|
ELECTRICAL
|
- SIEMENS 3000/3750 kva, Class OA, 12470Y/7200 to 480/277 volt, 3 phase transformer
- BEATEAU standard 1500 kva, Class OA, 12470GY/7200 to 480/277 volt, 3 phase transformer
- (3) 500 kva, 12470/7200 to 480/277 volt pole mounted transformers
- (2) SIEMENS Type SBA2020, 2000 amp ground fault breaker panel, 2000 amp main, (2) 800 amp, (2) 400 amp breakers
- (2) SIEMENS SBA2020, 2000 amp ground fault breakers
- G.E. 2000 amp AV line switchboard w/TPVF6620, 2000 amp breaker
- G.E. 2000 amp AV line switchboard w/(7) fused disconnects
- (2) SIEMENS 1200 amp, 12470/7200 volt fused disconnects
- G.E. 4000 amp AV line switchboard w/1200 & 800 amp breakers
- SIEMENS 3000 amp rated breaker panel w/(1) 800, (3) 600 & (1) 200 amp breakers
- ALLEN BRADLEY 7-section, 21-station, 709 seriesA.B. 4-section, 23-station, 509 seriesA.B. 8- section, 12-station w/(1) size 6, (4) size 4's reduced voltage startersA.B. 8-section, 24-station, 709 seriesA.B. 15-section, 39-stationA.B. 10-section, 10-stationA.B. 9-section, 18-station w/adjustable frequency & SMC startersA.B. 9-section, 26-station, 505 seriesA.B. 13-section, 37-stationA.B. 2-section, 11-station
- (2) ALLEN BRADLEY 1-section, 5-station, 509 series
- (2) G.E. 8000 line, 3-section, 10-station MCC
- Plus large quantity stand alone A.B. SMC 509, 505 series starters, breakers, lighting transformers w/ panels, PLC's, (2) electric shops, adjustable frequency controllers, spooled wire, GREENLEE 2" cap. Smart bender, ENSLEY E825 conduit bender, ENERPAC conduit bender, GREENLEE 690 fish tape system, conduit & wire, tech cable & trays throughout sawmill site, & much more
|
|
MACHINE SHOP EQUIPMENT
|
- AJAX HERCULES 18"x8-«' C.C., QCGH gap bed engine lathe
- WARNER 2 hp vertical milling machine
- AIRCO 4805 straight line cutter w/15' table
- ELLIS #60 horizontal miter metal cutting bandsaw
- JOHNSON #J horizontal metal cutting bandsaw
- (2) 50 ton hydraulic shop presses
- LINCOLN SA 200 gas welder
- MILLER Bobcat CC-CV ac/dc gas welder/generator
- (2) LINCOLN DC 600, LINCOLN R3R 500, (3) LINCOLN R3R 400, LINCOLN R3R 300, (2) MILLER SRH 333, AIRCO CV200 dc arc welders
- Plus: abrasive cutoff saws, RIDGID 535 threader, oxy/acetylene sets, broach set, granite surface plates, assorted inspection equipment, and much more
|
|
STORAGE CONTAINERS
|
- (7) 8'x8'x40' steel storage containers
|
|
BUILDINGS/OFFICE & LUNCH ROOM TRAILERS
|
- 1995 SUN STEEL 242'x160'x36' eave clear span bolt together sawmill building, 400W HID lights, sprinklers, second floor substructure, catwalks
- 70'x72'x28' eave all steel, bolt together clear span building w/24'x40' extension
- 72'x74'x23' eave all steel bolt together clear span building
- 35'x35' clear span bolt together 2 story debarker building
- 22'x50' clear span bolt together cutoff saw building
- 10'x25' wood frame office trailers, skid mounted
- 1987 24'x42' office trailer
|
|
PACKAGE BREAKDOWN HOISTS
|
- 13' 4-arm tilt package breakdown hoist, 52" arms, 88" lift, G.E. Pacific drive
|
|
VIBRATORY CONVEYORS
|
- 66'x22" pan bottom conveyor
- 90'x24" pan bottom conveyor
- MILLPOWER 45'x24" pan bottom conveyor
|
|
METAL DETECTORS
|
- MDI wrap around whole log metal detector w/paint pot, 18'x24" feed thru belt, fiberglass trough, SKK 7-1/2/30
- MDI CCW65A metal detector, 22" bottom fiberglass trough
|
|
PLUS EQUIPMENT OVER 3 DAYS
|
- (200+) assorted log decks, log hauls, lumber chain transfers, singulators, lumber landing tables, belt & chain conveyors, rollcases w/SKK, FALK, DODGE, MITSUBISHI, & assorted drives, quantity of noise controlled operators booths, hydraulic support units, (2) L.H. chop saws, (28) 19'x52" gravity discharge lumber stacking rollcases, lumber stacking carts, self dumping dumpsters, steel log bunks, laser alignment tool, tank mounted air compressors, air line systems, air receiver tanks throughout (3) plants, hydraulic hose fitting crimp machines, AMERICAN PB4523 pressure washer, electric chain hoist, steel tables & vises, (250+) spare motor inventory, (50+) pallet chain inventory, scissor lifts, bearings, cylinders, sprockets, sheaves, taper locks, V-belts, conveyor belting, scrap choppers, cameras & monitors, space heaters, job boxes, gas trash pumps, hydraulic pumps, oil storage tanks, concrete retaining wall blocks, pallet & parts room shelving, structural steel, scaffolding, plankways, shafting, DEWALT radial arm saw, large quantity of office equipment & furniture, & too much more to list!
|
DAY 2 ARLINGTON REMAN PLANT
RESAWS
|
- TURNER 42" quad line bar resaw, (4) 50 hp drive motors, hydraulic press feed rolls, hydraulic unit, 24'x27" infeed rollcase, new spare wheel
- (2) 1993 MID OREGON horizontal re-rip saws, 7-1/2 hp arbor motors, hydraulic feed & press rolls, hydraulic support unit, electrics, s/n: 29328
|
|
EDGERS
|
- Shop built 26" fixed saw fence board edger, 60 hp
|
|
TRIMMER
|
- IRVINGTON MOORE 20'x4" cut L.H. line shaft trimmer, 40 hp line shaft motor, 10-strand feed thru lugged chain transfer, end evening rollcase
|
|
PLANER
|
- 1995 COASTAL A2-613-8-94-95 6-head, 20-knife, 13"x6" cap. planer/matcher/profiler, 150 hp top, 75 hp bottom, 75 hp outside side, 50 hp inside side, 50 hp top profile, 75 hp bottom profile heads, hydraulic feed rolls, quick change cylinders, digital power adjustable side to top heads, HYDROLOCK heads, electronic head brake system, hydraulic unit w/(3) 40 hp pumps, manifold electrics, s/n: 1189044966
- 6' canted roll planer bridge
- 30'x30" canted roll pineapple feed table w/40 hp d/c drive, MG set, 10' H78 infeed transfer
- Assortment of side heads, planer cylinders, jointer bars, pattern knives & planer steel
|
|
HULA SAWS
|
- IRVINGTON MOORE hula saw system w/(2) 22", 5 hp saws
- Gravity rollcase 26'x12" waste belt conveyor
- Shop built hula saw system w/(2) 22", 5 hp saws
- Gravity rollcase 27'x12" waste belt, 30'x17" product belt conveyors, SKK drives
|
|
FENCING DOG EAR LINE
|
- 3-arm tilt package breakdown hoist w/scissor lift, 20'x60" side load infeed rollcase
- 4'x6' fencing singulator tranfer
- 2-section dog ear cut station w/(2) 3 hp/3450 rpm saws, feed thru transfers
- 3-arm overend package stacker w/15' infeed, dealing arms, end evening rolls, package hoist w/15 hp hydraulic unit, 20'x60" package outfeed rollcase
- Short unit hydraulic end evening squeeze w/48"x48" side platens, 9' cap., 40 hp hydraulic unit
- ALLEN BRADLEY 3 section dog ear line MCC
- Unit wrap station
- 16'x50' welded steel dog ear building
|
|
STRAPPING & WRAPPING LINES
|
- SIGNODE M22LP44 auto package strapper w/edge protectors, top & side squeeze, unit end evening press, 90'x54" feed thru rollcase, 22' 4-strand H82 chain in & outfeed decks, (2) hydraulic support units, lumber wrap station, ALLEN BRADLEY PLC controlled
- SIGNODE HPS stretch wrap machine w/7' tower, power head, 4' rotary table, s/n: F11072
- (3) complete INTERMEC 3400 bar code label printers w/wand systems
|
|
HOGS
|
- REXWORKS Megagrind 800 trailer mounted portable hog w/RAWLINS 72"x48" horizontal feed, bottom discharge high inertia rotary hog, clam shell opening, hydraulic feed roll, CAT 3412, 800 hp diesel, 17'x72" feed belt, 25'x48" take away belt, 51'x10', 3 axle carrier, s/n: M51001 (*sold subject to confirmation)
MORRIS KNUDSON 24x24 high inertia rotary hog w/clam shell opening
|
|
CHIP BINS
|
- PEERLESS 30-unit hydraulic chip bin
- 14-unit pneumatic chip bin w/long neck cyclone
|
|
AIR COMPRESSOR
|
- QUINCY QNW380E air cooled rotary screw compressor, 100 hp, s/n: 740264
|
|
FILING & GRINDING ROOM
|
- NEWMAN G280 rotary tub grinder, s/n: 280189
- NIELSEN 850 automatic side head grinder
|
|
ELECTRICAL
|
- ALLEN BRADLEY 4-section, 12-station MCC, 509 series
- A.B. 2-section, 9-station MCC, 709 series
- SQUARE D 5-section, 22-station MCC
- WESTINGHOUSE 2-section, 11-station
- A.B. 200 hp SMC starter
- Large quantity of stand alone electrics, power conduit & wire on reman plant site
|
|
TRUCK SCALES, LOADING DOCKS, TRAILER LOADERS, STORAGE CONTAINERS
|
- 1995 UNIBRIDGE 10'x80' V13SR801040 80 ton load cell truck scale, digital readout, printer, scale house(removal after July 2)
- CARDINAL 10'x80' 60 ton beam truck scale, IQ Plus digital readout, printer, scale house
- COPPERLOY 7'x35' hydraulic lift portable steel loading dock
- ROBBIN MYERS 4 ton bolt together log trailer loader
- (7) 8'x8'x40' steel storage containers
|
|
PACKAGE BREAKDOWN HOISTS
|
- 14' 4 arm tilt package breakdown hoist, 50" arms, 54" lift, SM CYCLO drives, 20' 5-strand H78 chain infeed package deck
- 14-1/2' 4 arm tilt package breakdown hoist, 52" arm, 60" lift, SM CYCLO drives
- 17' 4 arm tilt package breakdown hoist, 50" arms, 66" lift, 26' 4 strand HD82 chain package deck, US & SM CYCLO drives
- (2) dismantled breakdown hoist systems
|
|
SURPLUS EQUIPMENT (NOT INSTALLED)
|
- CAN CAR 5' linear positioning air strain quad bandmill w/hydraulic press feed rolls, (4) 100 hp drive motors, s/n: 102171
- FILER & STOWELL 5' air strain quad bandmill w/(4) 125 hp drives
- ALBANY 6' horizontal bandsaw
- FILER & STOWELL 5' air strain tilt resaw bandmill w/in & outfeed tilt rollcases
- (2) CME #34 opposed slabber system
- 1991 POWELL WANE right fixed 2-saw edger w/central chain feed
- SCHURMAN 6DAS24 fixed saw board edger
- BLACK CLAWSON 6120 60", 6-knife tilt disc chipper
- (2) 52" circular log chip saws, 75/100 hp
- 48" swing arm log cutoff saw, 40 hp
|
|
ROLLING STOCK DAY 2 SOLD AT ARLINGTON SAWMILL
|
- 1992 CATERPILLAR 988B rubber tire loader, power shift trans, diesel, MEDFORD log forks, s/n: 50W9236
- 1990 CATERPILLAR 980C articulated rubber tire loader, power shift trans, diesel, MEDFORD log forks, slide on G.P. bucket, s/n: 63X09424
- 1997 VOLVO L-330C articulated rubber tire full load log loader, diesel, MEDFORD forks, s/n: L330CV60024(*sold subject to confirmation)
- 1987 KOMATSU WA600 articulated rubber tire loader, diesel, MEDFORD log forks, s/n: 10196
- 1973 CATERPILLAR 980B articulated rubber tire loader, power shift trans, diesel
- 1978 CATERPILLAR 966C articulated rubber tire loader, power shift trans, diesel, G.P. bucket, s/n: 76J13416
- 1989 CATERPILLAR EL300 High Walker crawler log loader, expandable tracks, PIERCE boom, swivel grapple, tilt cab
- 1991 CATERPILLAR 235C crawler log loader, expandable tracks, YOUNG boom, swivel grapple, tilt cab
- 1987 CATERPILLAR 235B crawler log loader, expandable tracks, YOUNG boom, swivel grapple, tilt cab
- 1990 CATERPILLAR 225B crawler log loader, expandable tracks, YOUNG boom, swivel grapple, tilt cab
- 1988 JOHN DEERE 892DLC crawler log loader, LANCE boom, grapple, tilt cab
- 1985 GROVE RT522 22 ton all terrain hydraulic crane, CUMMINS diesel, STERLING boom, jib, swing cab, 2 axle steering, outriggers
- 1992 HYSTER H210XL 21,000 lb dual pneumatic forklift, enclosed cab, sideshift, Monitrol, PERKINS 6 cyl diesel, s/n: C007D01979N
- 1989 HYSTER H200H 20,000 lb dual pneumatic forklift, enclosed cab, sideshift, Monitrol, diesel, scale, s/n: C007D03433K
- 1988 TAYLOR TEB200S 20,000 lb dual pneumatic forklift, enclosed cab, sideshift, diesel, s/n: SC319607
- 1987 HYSTER H200HS 20,000 lb dual pneumatic forklift, enclosed cab, sideshift, propane, s/n: C007D02820H
- 1997 HYSTER H155XL2 15,000 lb dual pneumatic forklift, enclosed cab, sideshift, Monitrol, PERKINS 4 cyl diesel, s/n: F006D02877T
- 1992 HYSTER H155XL 15,000 lb dual pneumatic forklift, enclosed cab, sideshift, 3 spd trans., 6 cyl propane
- 1981 CATERPILLAR V180B 18,000 lb dual pneumatic forklift, enclosed cab, sideshift, 3 spd power shift, 2308 diesel, s/n: 68Y00542
- 1992, 1991 HYSTER 8,000 lb pneumatic & dual pneumatic forklifts, sideshift, 3 stage mast, propane
- 1979 HYSTER S-80E 8,000 lb forklift, propane
- 1977 HYSTER S-70B 7,000 lb forklift, propane
- CATERPILLAR T-50B 5,000 lb forklift, propane
- TOWMOTOR LT56 forklifts
- BOBCAT 753 skid steer loader, diesel, GP bucket w/clamp attachment, s/n: 515812261
- 1980 JOHN DEERE 2040 diesel tractor
- 1986 KENWORTH T800 T/A tractor, CUMMINS 400 hp, 9 spd FULLER
- 1982 FORD F700 service truck, V-8 propane, 5/2 trans, 14' bed, welder, compressor
- 1967 INTERNATIONAL DF400 4,000 gallon water truck
- INTERNATIONAL L-160 fire truck
- 1974 MACK MB600 T/A sawdust truck w/aluminum dump box
- 1981 KENWORTH 10/12 yard dump truck
- 1979 MACK 10/12 yard dump truck
- 1978 FORD LT9000 flatbed truck
- Quantity of pickup trucks
- 1977 UTILITY 40' T/A flatbed trailer
- 1975 TRAILMOBILE 40' T/A flatbed trailers
- (2) 1968 UTILITY 24', 3 axle pup flatbed trailers
- Single axle utility trailer
|
DAY 3 OSO SAWMILL
DEBARKERS
|
- MORBARK debarker w/14", 150 hp debarking head, 20" hydraulic driven log turning spike rolls, hydraulic support unit, control cab
|
|
LOG CUT OFF SAW
|
- 4-1/2' bar chain log cut off saw, 10 hp drive, log cradle
|
|
PEDESTAL LOADER
|
- PRENTICE 110BC pedestal mounted hydraulic log loader w/hydraulic unit
|
|
PRIMARY LOG BREAKDOWN SYSTEMS
|
- FILER & STOWELL 18'x40" 3 knee linear positioning 5-truck log carriage, INOVEC 5PC setworks, rail, bumpers, 150 hp d/c carriage drive w/MG set, cable, spools
- UNION IRON WORKS 7' R.H. mechanical strain head rig bandmill w/200 hp/886 rpm drive motor
- CME #64RH linear positioning pre-slabber, 200 hp
|
|
RESAW
|
- PACIFIC 5008D 54" R.H. mechanical strain line bar resaw w/100 hp drive motor, linear positioning line bar w/press feed rolls, INOVEC 5PC setworks, hydraulic support unit, 25' infeed rollcase
|
|
EDGERS
|
- SCHURMAN 24"x6" splined arbor fencing gang edger w/300 hp arbor drive motor, 30 hp gearhead feed roll drive, WATER MISER mist system, 17' canted roll infeed rollcase
- SCHURMAN 8HD48 8"x48" bottom splined arbor combo edger w/(4) linear positioning saws, 250 hp arbor motor, INOVEC setworks, lasers, hydraulic support unit, 20' split canted roll infeed rollcase, 20'x48" take away belt, s/n: 641
- ROSE MACHINERY pocket edger w/10 hp horizontal circular saw, 1-1/2" feed thru belt, sawdust blower, electrics
|
|
TRIMMER
|
- IRVINGTON MOORE 66 R.H. 20' cut, 24' pass individually motorized trimmer w/feed thru lugged chain transfer, end evening rollcase, minus fence, minus saw, s/n: 20540R
|
|
CHIP SCREEN/CHIP BIN
|
- BMW 4'x12' 3-deck chip shaker screen
- PEERLESS 20-unit hydraulic chip bin
|
|
AIR COMPRESSOR
|
- QUINCY QNW350B air cooled rotary screw compressor, 75 hp, s/n: 790134
|
|
FILING & GRINDING ROOM
|
- ARMSTRONG #4 L&R hand bandsaw sharpeners, s/n: 13460
- ARMSTRONG #4 stretcher roll, s/n: 10131
- Hoe saw guide shaper
- Dual side edger guide milling machine
- Assortment of pneumatic swages, band & circular saw blades & grinding wheels
|
|
ELECTRICAL
|
- ALLEN BRADLEY 6-section, 19-station MCC w/SMC size 6 starter
- A.B. MCC w/(11) plug in boxes, 709 series
- CUTLER HAMMER 2-section, 11-station MCC
- SQUARE D 2-section, 10-station MCC
- ULTRA-MIZER size 6, size 4 soft starts
- SAFTRONICS 150 hp soft start
- INERTIA SYSTEMS size 5 soft start
- FURNAS size 5 reduced voltage
- Large quantity stand alone electrics, power conduit & wire throughout plant site
|
|
MACHINE SHOP EQUIPMENT
|
- Horizontal metal cutting bandsaw
- RIDGID 535 threader
- JET 20" drill press
- LINCOLN Idealarc R3S250, MILLER ac/dc welding power sources
|
|
BUILDINGS
|
- 140'x80'x20' eave clear span bolt together sawmill building
- 25'x40' welded steel clear span green chain building
|
|
PACKAGE BREAKDOWN HOISTS
|
- 6' 2-arm tilt package breakdown hoist, 52" arms 63" lift, G.E. PACIFIC drive
- 54" 2-arm tilt package breakdown hoist, 52" arms, 88" lift, hydraulic unit
|
|
VIBRATORY CONVEYORS
|
- VIBRA-PRO 55'x18" pan bottom
- 28'x22" pan bottom
|
|
METAL DETECTORS
|
- MDI CR85 wrap around whole log metal detector w/10'x24" feed thru belt, FALK drive
- MDI CCW78 metal detector, 18" bottom fiberglass trough
|
|
TERMS AND CONDITIONS
|
- 7% BUYERS PREMIUM
- PAYMENT: Full payment must be made by no later than 4pm, Friday, May 18.
- A 25% deposit is required by the close of business, auction day.
- Cash, cashiers check, Master & Visa Cards only. Personal or company checks accepted ONLY with bank letter of guarantee.
- Absentee bids accepted with 25% deposit
- REMOVAL: No purchase may be removed during the auction unless otherwise announced by the auctioneer. All purchases must be removed 1 hour after the sale each day or between 7 am & 3:30 pm Monday through Friday, May 21 through 25 for small items. Large equipment removal schedule announced on each auction day.
- Announcements made by the auctioneer at the time of sale take precedence over printed matter.
- Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
- Due to safety & insurance reasons, persons under 12 not admitted.
- Washington Auctioneers License #48
|
|
LODGING
|
| Hawthorne Inn & Suites | | (800) 527-1133 |
| Crossroads Inn | | (877) 856-3751 |
| Smokey Point Motor Inn | | (360) 659-8561 |
|
|
AIRPORTS & CAR RENTALS
|
- Sea-Tac International Airport - All Major Airlines & Rental Car Agencies (1-1/4 hr south of auction site)
- Arlington Municipal Airport - 5,333'x100' lighted runway, Jet & AV gas, AWOS 135.625
| U-Save Car Rental | | (360) 658-5785 |
| Enterprise Car Rental | | (360) 653-2319 |
|
|
DRIVER DIRECTIONS
|
- The auction site is approximately 50 miles north of Seattle.
- From north or southbound I-5, take the Arlington/Hwy 531 exit (#206).
- Drive east on Hwy 531 approximately 3/10 mile to Smokey Point Blvd.
- Turn left on Smokey Point Blvd and drive 1 mile to 188th N.E.
- Turn right on 188th N.E. and drive 8/10 mile to 47th N.E.
- Turn left on 47th N.E. and drive 2/10 mile to Day One sale site, on the right.
- Other auction locations within 15 miles of Day One site.
WATCH FOR AUCTION SIGNS
FOOD SERVICE AVAILABLE AT THE AUCTION SITE
|
|
ORDER OF SALE:
|
- DAY 1
- Arlington Small Log Sawmill
- Machine, Electrical Shops
- Filing & Grinding Rooms
- DAY 2
- Arlington Reman Plant
- Rolling Stock @ Arlington Sawmill
- Arlington Sawmill Surplus Equipment Inventory
- DAY 3
- Oso Sawmill
|
|
Home | About Us | Auction Schedule | Mailing List | Map | Past Auctions
Registration Form | Advanced Bid Overview | Terms & Conditions
 Back to Top
James G. Murphy Co.
Commercial / Industrial / Real Estate Auctioneers
P.O. Box 82160 - 18226 - 68th Ave. N.E.
Kenmore, Washington 98028
(425) 486-1246 or Toll Free 1-800-426-3008
Fax: (425) 483-8247
Oregon address & phone:
105 McNary Estates Dr. N
Keizer, OR 97303
phone: (503) 463-4444
fax: (503) 463-1554
Copyright©1997-2005 James G. Murphy Co.
All rights reserved worldwide
|
|
|
