Click small pics to enlarge

Click HERE for more photos


STAKES

9AM - THURSDAY - OCTOBER 4
Preview 10-4, Wednesday, October 3
150 Taylor Way, Blue Lake, CA

Past Auction held in 2007

Display Catalog | X Lots

Downloadable PDF Catalog

Advance Bid Center

MILL & REMAN EQUIPMENT
  • STETSON ROSS 6"x15" 6-head, 10-knife planer matcher line, 50 hp top, 25 hp bottom & side, 10 hp top & bottom profile heads, INDUSTRIAL ELECTRIC 25 hp DC feed drive, 40 hp MG set, STETSON ROSS 18' single pineapple feed table, (4) 8"x28" canted smooth, (2) spiral rolls, 4' bridge, hold down rolls, shoe, 27' 2-section 5-strand infeed transfer, 16' 5-arm tilt hoist, 54"x52" travel arms, gearhead motor, brake, 12"x23' outfeed belt, gearhead motor, 12"x60" slow down belt, MOORE 2"x24" lumber swede, approx 100 hp planer blower, (3) spare arbors, profile stands, (50+) spare heads, (4) 25 hp motor rewinds, s/n: 2643
  • ECKSTROM CARLSON 4"x6" 4-head, 8-knife top & bottom moulder, 30 hp top, 15 hp bottom & sides, TOSHIBA 7-1/2 hp feed drive motor, ABB ACS 500 frequency drive, 11' 2-strand H78 infeed transfer, gearhead motor, in & outfeed gravity rolls, (20+) spare heads, approx 20 hp blower
  • MATTISON 274 moulder w/(4) heads, 10 hp top & bottom, 5 hp side heads
  • MERSHON 48" twin vertical band resaw, 40 hp, hydraulic driven feed rolls, 30 hp hydraulic unit, 5"x18' belt transfer infeed, hydraulic drive, 12"x12' outfeed belt, gearhead motor, 4'x7' scissor lift infeed, gravity rolls, clean out conveyors, screw auger w/motors, blower & electrics, spare saws, s/n: 7084
  • 1998 BAKER BBR-O horizontal band resaw, 20 hp, 5-1/2"x7' feed thru belt w/hydraulic drive, hydraulic top rolls, s/n: 98-2652
  • PRODUCTO 76S1 resaw, 50 hp, 25 hp hydraulic unit, hydraulic feed rolls, 6"x19' infeed, 6"x5' outfeed transfer belts w/hydraulic drives, s/n: 2540685
  • TURNER 42" single vertical band resaw, 20 hp, s/n: SBR993
  • ALBANY 40WA right hand, 20' cut, computerized 26' pass line shaft trimmer, 50 hp, (11) 20" saws, 9' 20-strand lugged feed thru transfer w/even ending rollcase, 9' 5-strand H78 infeed transfer, SKK gearhead, 5' 6-strand H138 lumber landing table, gearhead motor, 10"x37' waste belt, 19"x26' belt transfer, electrics, controls, spares, s/n: 191
  • SUMNER 2-saw hula station w/18" saws, feed thru gravity rolls, approx 10 hp hydraulic unit, outfeed transfer belt, SKK gearhead motor, 12"x22', 12"x40' waste belt transfers, 16', 18' 5-strand H78 infeed transfers, 12' 5-arm mechanical tilt hoist w/50"x76" travel arms
  • Custom built 14' cut, pass 14', 5-saw trimmer, zero saw w/adjustable saws, 8' 8-strand feed thru transfer
  • Custom built 12' cut, pass 14', 5-saw trimmer, zero saw w/(4) adjustable saws, 8' 8-strand lugged feed thru transfer
  • Custom built portable 8' double end trimmer
  • MONTGOMERY approx 10"x20" hammer hog, 50 hp, 12"x39', 9"x14' infeed belts w/drives
  • BLACK CLAWSON 36" 10-knife chipper, 50 hp, drop feed, bottom discharge, s/n: 2869-64
  • NEWMAN G81 travel bed profile grinder, s/n: 13553
  • STETSON ROSS travel bed profile grinder
  • AMERICAN WOODWORKING MACHINERY travel bed profile grinder
  • HANCHETT DN42 42" travel bed grinder, s/n: 90541
  • Custom built bolter/rip saw w/(2) saws, approx 20 hp, 6"x7' infeed belt transfer, 8' powered outfeed rollcase, (8) 5"x15" spiral variable speed rolls, 14' 3-strand H78 infeed transfer
  • Custom built lath/multi ripsaw w/top sizing heads, 30 hp ripsaw arbor motor, 40 hp sizing head motor, clean out conveyor
  • Custom built lath/multi ripsaw w/top sizing head, 30 hp ripsaw arbor motor, 25 hp sizing head motor, clean out conveyor
  • Custom built lath machine, 40 hp/3470 rpm arbor drive, 15 hp sizing head, variable speed feed rolls
  • Custom built 4"x6" block saw w/(8) saws, approx 50 hp, 6' 4-strand feed thru transfer, 51"x20' outfeed belt, 10"x17' clean out belts w/gearhead motors
  • HEIAN RS 300 straight line ripsaw, approx 20 hp, feed thru dip chain
  • SMITH PRODUCTS ripsaw, 7-1/2 hp, variable speed feed rolls
  • Custom built ripsaw
  • Custom built 1"x2" stake pointer machine w/3-saw end trim station, 5-strand feed thru transfer, 2-saw stake point station w/3-strand feed thru transfer, 13"x13' clean out belt, in & outfeed belt transfers
  • Custom built 1"x1" stake pointer w/(2) PERSKE 3500 rpm vertical mounted motors, powered chains, 1/3 hp feed
  • Custom built 2-saw stake pointer w/hogging heads, 2" x random width
  • Custom built 2-saw stake pointer, 2"x2" capacity
  • Custom built dog ear machine w/(2) saws, feed thru incline trimmer, precision end trim saw
  • Custom built dog ear machine
  • Custom built mortiser
  • BAUER RC 25E3 25 hp compressor, 104 cfm @ 125 psi, 9674 hrs, s/n: 10050
  • QUINCY 390 15 hp tank mounted compressor
  • Approx 10 hp 2-cylinder tank mounted compressor
  • 36"x72" vertical air receiver tank
  • Dual trailer chip loading station w/(2) 40' chains, flites, chip conveyors, 20' crossover chip conveyor, infeed chip conveyors, approx 8', 6', & 4' cyclones, piping
  • 97' 2-section H138, H78 6-strand planer dry chain w/gearhead motor
  • 78' 6-strand hula station pull chain w/motor to reducer
  • GRUTTER 1600 right hand chop saw station w/infeed belt,outfeed gravity rolls, lumber stops, 15' 3-strand outfeed transfer, 12"x7' waste belt, 3'x5' scissor lift
  • (6) HITACHI 15" miter saws w/gravity rolls & lumber stops
  • 52' powered rollcase w/(14) 8-1/2"x60" rolls
  • Approx 24" 20 hp blower w/36" long neck cyclone
  • 20"x60" fiberglass trough
  • (10,000+) 3/4"x1-1/2"x46"-52" stickers
  • (60+) steel lumber carts
  • Block bins
  • PADOVA ITALIA JS 22"x84" engine lathe, 1-1/2" bore hole, 3 & 4-jaw chucks, (2) steady rests, tool post, tooling, tail stock, s/n: 01462
  • COMET universal milling machine, 75-2750 rpm spindle speeds, 2 hp head, 9"x42" T-slot power feed table
  • PERINE MACHINERY CO 42" radial arm drill, 9" column, 22-1/2"x22-1/2" slotted knee
  • BURGMASTER 6-tool turret drill table, JACOBS 3B 1/8"-5/8" drill chucks
  • JOHNSON J horizontal metal cutting bandsaw, s/n: J16250
  • 30"x36" hydraulic shop press, 3 hp
  • CANNEDY OTTO 24" hydraulic drill press w/16" table
  • OHIO MACHINE TOOL CO over arm shaper
  • (2) LINCOLN AC225 arc welders
  • WILTON SP-4 plastic bander; CLIMAX key mill; (2) 550 gallon diesel & gas tanks; (2) WESTINGHOUSE 1200 amp, 600 volt disconnects; starters to size 3; disconnects to 1200 amp, transformers to 30 kva; motors to 125 hp; lights; benches; shelves; banding carts; chain; sprockets; pulleys; belting; steel carts; vises; hand tools; portable fans; rolls; conduit & fittings, gravity rolls; bearings; cylinders; nuts & bolts; machine tooling; parts washer; plumbing; air sprayers; barrel pumps; couplers; hubs; power tools; electrical stores; belts; UHMW; breakers; hydraulic hoses; forklift parts; railroad jacks; much more

BUILDINGS
  • WEDGCOR 60'x120' all steel clear span building w/lights & engineering
  • 50'x105', 30'x50' planer/gang building, wood framed metal clad w/lights & engineering
  • 30'x105', 20'x30' hula building, wood framed metal clad w/lights & engineering
  • 32'x40' shed roof, lath area

ROLLING STOCK
  • HYSTER CHALLENGER 165 16,500 lb dual pneumatic forklift, diesel, 212-1/2" 2-stage mast, 54" forks, sideshift, scales, s/n: B7P7174T
  • HYSTER CHALLENGER 150 15,000 lb dual pneumatic forklift, gas, 192" 2-stage mast, 54" forks, sideshift, s/n: B7P6271S
  • HYSTER H150E 15,000 lb dual pneumatic forklift, gas, 206" 2-stage mast, 54" forks, scales, s/n: B7P1606H
  • HYSTER H130F 13,000 lb dual pneumatic forklift, gas, 198" 2-stage mast 54" forks, sideshift, s/n: D6D1613
  • HYSTER H80C 8000 lb dual pneumatic forklift, gas, 142" 2-stage mast, 48" forks, sideshift, s/n: 5D5271K
  • (2) MERRITT 45' T/A aluminum chip trailers

TERMS & CONDITIONS
  • 10% BUYERS PREMIUM
  • PAYMENT: Full payment must be made by no later than the close of business, auction day.
  • Cash, cashiers check, Master & Visa Cards, wire transfers only. Personal or company checks accepted ONLY with bank letter of guarantee.
  • Absentee bids accepted with 25% deposit
  • REMOVAL: No purchase may be removed during the auction unless otherwise announced by the auctioneer. Removal schedule to be announced on auction day.
  • Announcements made by the auctioneer at the time of sale take precedence over printed matter.
  • Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
  • Due to safety & insurance reasons, persons under 12 not admitted.

  • Washington Auctioneers License #1960

DRIVER DIRECTIONS
  • From east or westbound CA-299 take the Blue Lake Blvd exit (#5).
  • Drive east on Blue Lake Blvd to Greenwood Ave. Turn right on Greenwood and drive to Hatchery Rd.
  • Turn right on Hatchery Rd and drive to Taylor Way.
  • Turn right onto Taylor Way. The auction site is located in the Blue Lake Industrial Park.

WATCH FOR AUCTION SIGNS

FOOD SERVICE AVAILABLE AT THE AUCTION SITE



Home | About Us | Auction Schedule | Immediate Sales | Email Signup | Map | Past Auctions | Registration Form | Advanced Bid Overview | Terms & Conditions | Best of 2000-2004 Auctions



James G. Murphy Co.
Commercial / Industrial / Real Estate Auctioneers
P.O. Box 82160 - 18226 - 68th Ave. N.E.
Kenmore, Washington 98028
(425) 486-1246 or Toll Free 1-800-426-3008
Fax: (425) 483-8247

Oregon address & phone:
105 McNary Estates Dr. N
Keizer, OR 97303
phone: (503) 463-4444
fax: (503) 463-1554


Corporate Media Arts Group

Copyright©1997-2007 James G. Murphy Co.
All rights reserved worldwide