Click small pics to enlarge

Click HERE for more photos


9AM - TUESDAY - MAY 19
Preview 8-4, Monday, May 18
Willits, CA

Display Catalog | X Lots

Downloadable PDF Catalog

Advance Bid Center

Equipment Just Added
    Fire Pump System
  • DETROIT 115 hp, 4 cylinder diesel engine, s/n: 4A02117192 w/ALLISON PTO model PTA-1SD273, AMARILLO 100 hp righ angle gear drive to DURCO 2x3x1.5 pump w/10 hp motor, GE 100 hp motor to AP 1000 gpm centrifugal pump, MASTER & SYLVANIA fire pump controllers, all batteries, fuel tank, piping, valves & electrical w/building

Sawmill & Planermill Equipment
  • MCDONOUGH 54" single band, double column vertical band resaw, 75 hp, air strain, roll tilting feedworks, ACCU-LUBE system, IES 100 hp static RVS, 30' powered infeed rollcase w/(11) 9"x24" rolls, US vari speed drive, 16' outfeed rollcase, (7) 8"x23" rolls, drive, GE 8000 line 2-section MCC w/(7) switches, (2) BALDOR adjustable speed drives, spare band saws, s/n: 54-1565
  • 1998 STENNER ST-9 36" single band vertical resaw, 20 hp, powered feed roll, 25-100 fpm, 0-35O tilt, 9" max opening, feed rolls to saw, 12" max opening fence to saw, 14-1/2" max height thru saw, spare band saws
  • TURNER 48" single vertical band resaw, RELIANCE 50 hp, hydraulic vertical feed rolls, 5 hp hydraulic unit, ACCU-LUBE system, GE CR106EO RVS, 17' powered infeed rollcase, (11) 6"x17" rolls, European vari speed drive, 12"x18' outfeed belt, SKK gearhead motor, spare band saws, s/n: 2139
  • PRODUCTO 79-2P-MG resaw, 100 hp arbor drive, hydraulic driven in & outfeed rolls, 15 hp hydraulic pump, 6"x20' hydraulic infeed belt, 12"x60" hydraulic outfeed belt, spare saws, s/n: 2591285
  • E. PAULSEN 36" horizontal band resaw, 50 hp arbor drive, 10 hp hydraulic unit, portable headrig, not installed
  • TRI-STATE select ripsaw w/17" splined bottom arbor, 50 hp/3460 rpm drive, 24-valve setworks, powered in & outfeed rolls, air hold downs, 19' single pineapple feed table, (17) 4"x24" rolls, 6' 5-strand infeed transfer, 30"x21' outfeed belt transfer, not installed, s/n: 349186
  • STETSON ROSS 6-12-A1 planer/matcher, 8"x15", 6-heads, 12-knife, 80 hp top, 40 hp bottom, approx 25-35 hp sides, 40 hp top, 20 hp bottom matcher heads, REEVES vari speed drive on feed rolls, STETSON ROSS 503E, 22' single pineapple feed roll w/speed up roll, hold over shoe, (7) 8-1/2"x29" canted spiral & smooth rolls, 18"x6' outfeed belt w/vari speed drive, bridge, spare parts, heads, jointer bars, profile yoke, s/n: 2774
  • YATES A20 planer/matcher, 8"x15", 6-heads, 8-knife, 50 hp top, 25 hp bottom, approx 25 hp sides, 15 hp top & bottom profiles, GE 50 hp feed rolls drive, 16' single pineapple feed table, speed up roll, hold over shoe, (8) 5-1/2"x29" spiral rolls, 12"x21' outfeed belt w/drive, spare parts, heads, jointer bars, profile yoke, s/n: B2695
  • WOODS 134BM planer/matcher, 6"x12", 5-heads, 6-knife, approx 20 hp top, bottom & profile, 5 hp sides, hydraulic feed rolls, 15 hp hydraulic unit, spare parts, heads, jointer bars, s/n: 1423
  • DIEHL TFM68 moulder, 4"x8", 6-heads, 15 hp bottom, 5 hp sides, 15 hp top, 20 hp bottom, 5 hp speed roll drive, 30 hp MG set, spare heads, not installed, s/n: 1282/M4570-3954
  • (225+/-) spare planer & moulder heads
  • PACIFIC TRAIL MFG INC 7' bar type unit saw, 15 hp, 24' vee rail carriage, digital read out, controls
  • MACFAB TS44-26 bander w/top & side squeeze, bump gate, in & outfeed rollcases, partially installed, s/n: 1501
  • 1998 ADVANCED RECYCLING EQUIPMENT challenger type CH-100-30225 re-chipper, 18.5 kw motor, not installed, s/n: 0398H0131A
  • GOODMAN/DIAMOND 135 knife hog, approx 16"x35", drop feed, bottom discharge, TOSHIBA 50 hp
  • SUMNER IRON WORKS no. 35 knife hog, not installed, s/n: 1233
  • PEERLESS 21-unit hydraulic chip bin, 15 hp hydraulic unit
  • BLACK CLAWSON 612 6'x12' 2-deck chip screen
  • Approx 9' diameter long neck cyclone w/3/16" stainless steel liner
  • Approx 8' diameter cyclone
  • 2002 VIBRA PRO LS-120900FS-3/16 (MS) 70'F-3 hp, 12"x70' vibratory conveyor
  • 12"x56' vibratory conveyor, TOSHIBA 7.5 hp motor, not installed
  • RENS C240 metal detector, A10-30 search coil, s/n: 120588
  • 14' 4-arm mechanical breakdown hoist w/52"x64" travel arms, GE PACIFIC gearhead motor
  • 10' 3-arm mechanical breakdown hoist w/50"x53" travel arms, motor to reducer
  • 16' 5-arm mechanical breakdown hoist w/53"x52" travel arms w/gearhead motor, not installed
  • 18' 5-arm mechanical breakdown hoist w/58"x60" travel arms, motor to reducer, not installed
  • IRVINGTON hula saw w/20" saws, approx 5 hp/3500 rpm, (1 saw partial), air cylinder, gravity feed thru rolls, lumber stops, (2) 12"x20' belts
  • PRODUCTO DE-8ET dog ear trimmer w/(2) 45O saws, 7.5 hp, 6' 2-strand lugged feed thru transfer, 1 hp, quick adjust line bar w/sets to 4'-6' & 8'
  • GOOD-KO INDUSTRIES web saw, 5'-14' capacity w/(5) adjustable saws, camber adjustment, approx 5 hp, 6' 4-strand feed thru transfer w/motor, not installed, s/n: 1210
  • Custom built in line select trim saw
  • (2) MID OREGON 14" mechanical RH chop saws w/gravity rolls, lumber stops
  • GRUTTER 18" mechanical LH chop saw w/gravity rolls, lumber stops
  • 6400 lb capacity 4'x11' hydraulic scissor lift w/pump
  • 3'x6' hydraulic scissor lift w/pump
  • ROSS COOK combo unit BSE-815M-PJ dust collector w/(19) 4 5/8"x38" filters, 250 scfm, 15 hp fan, cone target box
  • CENTRAL CALIFORNIA size 60-100 blower, TOSHIBA 125 hp
  • CENTRAL CALIFORNIA size 50 blower, RELIANCE 40 hp
  • 16', (2) 8' diameter rotary tables w/drives
  • GARDNER DENVER 30 hp rotary screw compressor, 200 psi, s/n: 6971
  • JOY TWISTAIR 220 rotary screw compressor, 125 psig, s/n: 114062
  • Dual bag dust collector
  • Portable approx 30' box chain conveyor w/motor to DODGE reducer
  • (2) approx 70' H78 green chain transfers
  • (2) 6"x10' screw augers, BALDOR 1.5 hp
  • NEWMAN G200 tub grinder, s/n: 200186
  • STETSON ROSS 372 travel bed side head grinder
  • SUTTON travel bed pattern grinder
  • BALDOR 2 hp double end profile grinder
  • Profile set up stand, circle set up stands
  • ARMSTRONG 3-10C stretcher roll, s/n: 12332
  • ARMSTRONG #2 stretcher roll w/#12 welding clamp, anvil, s/n: 7002
  • ARMSTRONG #4 LH bandsaw sharpener, s/n: 2744
  • ARMSTRONG #2 LH bandsaw sharpener, s/n: 2393
  • ACME circle saw sharpener, s/n: 4882
  • HOE circle saw sharpener
  • PRODUCTO resaw fly cutter
  • MCDONOUGH guide cutter, s/n: BDM455
  • HOE guide cutter
  • ABB 1500 kva pad mounted transformer, 12470/480 volt, s/n: PAB2521
  • GE 1000 kva pad mounted transformer, 12000/480 volt, s/n: H88662
  • WESTINGHOUSE 2000 amp main w/800, (5) 600, (2) 400 amp breakers
  • WESTINGHOUSE 95 kilo volt disconnect switch w/current limit fuses, s/n: YCR99651
  • GE 8000 line, 3-section MCC w/(10) switches
  • GE 8000 line 2-section MCC w/(7) switches
  • BALDOR adjustable speed drives
  • Starters to 125 hp
  • AB 1336 drives
  • CLEAVER BROOKS CB760-300 natural gas fired boiler, 15 psi, 12554000 btu/hr input, DA tank, pumps, chemical & water make up tanks, s/n: L42787
  • WELLONS approx 24-unit fuel silo, cone bottom w/dual augers, single auger metering screw, s/n: 7703D
  • (4) Block constructed kilns w/4" kiln coils, 72" aluminum kiln fans w/approx 10 hp, MOORE/COE recorders, FOXBORO valves, wood doors
  • Approx 26'-28'H x 75'W x 190'L Douglas Fir pre drying shed
  • 3/4"x1 1/2"x2"x52" kiln stickers in racks
  • Assortment of shop equipment & tools including: LODGE & SHIPLEY 17"x68" engine lathe, 1-1/4" thru hole, 4-jaw chuck, steady rest, tool post, tail stock, threading, s/n: 7628; WELDAN POWER G8000 225 amp/8000 amp/115-230 volt welder generator; SWEED 450 scrap chopper; (20+/-) SIGNODE banders (manual & air); Plastic banding, carts & strapping tools; BT model L-2000U, 5000 lb pallet jack; WHITEMAN 42" gas concrete float; Gas yard goat; self dumping hoppers; steel bins; rail car frame; boneyard; Custom built truck ramp; (2) 4'x6' fuel tanks w/FILL RITE 15 gpm pumps, 2'x4' fuel tank; (2) CLIMAX 65 key mills; Mag base drill; MAKITA 10" tilting table saw; (20+/-) Spare forklift & truck tires; (100+/-) Spare motors; Portable belt conveyors; Transfers; Rollcases; Conveyors; Gravity rolls; Skate rolls; New DISPATCH oven; Large chip bin vibrator (new in crate); Spare parts; Gearboxes; Bearings; Spare bandsaws & round saws; Swages; Shapers; 5", 8" & 16" round saw anvils; (225+/-) spare planer & moulder heads; Office equipment, furniture & supplies; Much More!
  • Assortment of redwood lumber

Rolling Stock
  • (2) 1998 HYSTER H155XL dual pneumatic tire forklifts, 15,500 lb capacity, PERKINS diesel, 173-1/2" & 212-1/2" 2-stage mast, sideshift, 52" forks, s/n's: F006A10030V, F006A09640V
  • 1990 HYSTER H135XL dual pneumatic tire forklift, 13,500 lb capacity, PERKINS diesel, 173-1/2" 2-stage clearview mast, sideshift, 52" forks, s/n: F006A04789L
  • 1998 HYSTER H110XL dual pneumatic tire forklift, 11,000 lb capacity, PERKINS diesel, 156" 2-stage mast, sideshift, 54" forks, s/n: G005A09705V
  • 1981 HYSTER H180H dual pneumatic tire forklift, 18,000 lb capacity, PERKINS diesel, 211-1/2" 2-stage mast, sideshift, 54" forks, s/n: C007D02589C
  • NISSAN 80 CRGH02F35V solid tire forklift, 7000 lb capacity, 175" 2-stage mast, sideshift, 48" forks, s/n: CRGH02-000193
  • 1987 HYSTER H40XLM pneumatic tire forklift, 4000 lb capacity, ISUZU diesel, 155-1/2" 2-stage mast, sideshift, 48" forks, s/n: A177B18992J
  • CAT 922 Traxcavator rubber tire loader, CAT 4-cylinder diesel, 8' bucket, 14.00-24 tires, s/n: 94A2051
  • 1996 JLG 40HA manlift, FORD dual fuel engine, 500 lb platform capacity, 24' reach, 40' platform height, 25O max grade, 4325 hrs, s/n: 028326-0300024118
  • ADVANCE MACHINE RETRIEVER 56 5600-1 propane powered sweeper, front & rear brushes, s/n: 890337
  • 1995 GMC 1500SL dual wheel pickup, GMC turbo diesel, 5 speed, 12' NORTH BAY steel flatbed w/headache rack, stake pockets
  • 1973 INTERNATIONAL LOADSTAR 1600 truck, V8 gas, 4 speed, 14' steel flatbed w/headache rack, PENTEL hitch
  • 1982 INTERNATIONAL CARGO STAR C01850B single axle tractor, INTERNATIONAL turbo diesel engine, automatic
  • DODGE job rated dual wheel water truck, 241 cu in Hemi, 5 speed, approx 1000 gallon water tank, HONDA 5.5 hp pump, front & rear spray bars
  • 1959 WHITING TRACKMOBILE 5TM549 w/HERCULES flathead 6-cylinder gas, TOROMATIC drive, 56 gallon fuel tank, 12500 lt wt, 13000 lb draw bar pull, s/n: 5TM5149
  • FAIRMONT class MT14, series M, group 1 speeder/motor car, s/n: 25447
  • FAIRMONT RIO GRANDE speeder/motor car, s/n: 245085
  • CAT 12 motor grader, CAT diesel w/pony starter, 12' mold board, scarifier, s/n: 9K720
  • HYSTER MHC6878 straddle buggy, HERCULES 6-cylinder gas, s/n: 26107

TERMS & CONDITIONS
  • 10% BUYERS PREMIUM
  • PAYMENT: Full payment must be made by no later than 4pm, Wednesday, May 20.
  • A 25% deposit is required by the close of business, auction day.
  • Cash, cashiers check, Master & Visa Cards, wire transfers only. Personal or company checks accepted ONLY with bank letter of guarantee.
  • Absentee bids accepted with 25% deposit
  • REMOVAL: No purchase may be removed during the auction unless otherwise announced by the auctioneer. Removal schedule announced on auction day.
  • Announcements made by the auctioneer at the time of sale take precedence over printed matter.
  • Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
  • Due to safety & insurance reasons, persons under 12 not admitted.

  • Washington Auctioneers License #1960

LODGING & AIRPORT INFORMATION
    Lodging:
    Baechtel Creek Inn & Spa 707-459-9063
    Best Western Willits Inn 707-459-5800
    Super 8 Willits 707-459-3388


    Airports:
  • Arcata Airport - serves Delta, Horizon & United airlines
  • Sacramento International Airport - serves all major airlines
  • Santa Rosa-Sonoma County Airport - serves Horizon Air

DRIVER DIRECTIONS
  • From Hwy 101 in Willits, drive east on Commercial St. approx 3/10 mile to N. Lenore St., turn left and drive approx 2/10 mile through gate, stay right to the auction site

WATCH FOR AUCTION SIGNS

FOOD SERVICE AVAILABLE AT THE AUCTION SITE



Home | About Us | Auction Schedule | Immediate Sales | Email Signup | Map | Past Auctions | Registration Form | Advanced Bid Overview | Terms & Conditions | Best of 2000-2004 Auctions



James G. Murphy Co.
Commercial / Industrial / Real Estate Auctioneers
P.O. Box 82160 - 18226 - 68th Ave. N.E.
Kenmore, Washington 98028
(425) 486-1246 or Toll Free 1-800-426-3008
Fax: (425) 483-8247

Oregon address & phone:
105 McNary Estates Dr. N
Keizer, OR 97303
phone: (503) 463-4444
fax: (503) 463-1554


Corporate Media Arts Group

Copyright©1997-2009 James G. Murphy Co.
All rights reserved worldwide