Click small pics to enlarge

Click HERE for more photos

BIGHORN LUMBER CO

9AM - TUESDAY - JUNE 30
Preview 8-4, Monday, June 29
1100 S Pine, Laramie, WY

Display Catalog | X Lots

Downloadable PDF Catalog

Advance Bid Center

Pedestal Mount Log Loader
  • 1990 BARKO 275ASE hydraulic pedestal mount log loader, 100 hp, 30' BDH boom, rebuilt 42" HD grapples, enclosed cab, s/n: 17531

Debarker
  • CAMBIO 30 30" 5-arm ring debarker, LINDSAY air ring, WESTINGHOUSE 75 hp ring drive, infeed hold down rolls, powered outfeed tires, 15' 6"x9" box chain infeed log haul, BALDOR 7.5 hp motor to FALK 68 rpm reducer, 8' 6"x9" box chain clean out conveyor, BALDOR 5 hp to FALK reducer, controls, electrics in cab, s/n: 30AM19
  • (2) CAMBIO debarkers (parts only), spare air bags, gears, bearings

Whole Log Cut Off Saw & Metal Detector
  • 60" insert tooth whole log cut off saw, 30 hp/885 rpm arbor drive, air operated, 20' powered infeed hourglass rollcase, TECO 7.5 hp to FALK 125 rpm reducer, 52' 6"x12" box chain outfeed log haul, WEAVER 20 hp/1170 rpm to FALK 125 rpm reducer, controls, electrics in cab, spare saws
  • MDI TWA2000 whole log metal detector w/CR85 search coil, 46" wide x 38" high, 7' fiberglass trough, 36"x15' pass thru belt, s/n: 970610

HeadRig
  • SALEM 66" RH, 17° canted RH headrig, air strain, 150 hp/1185 rpm arbor drive, feed thru slat bed chain, hydraulic hood, GE 70CR starter, AB 3-section MCC, spare saws, parts, s/n: 48939R7

Carriage & Drive
  • 1989 SALEM 36"x12' 3-knee 17° canted RH chain block carriage, tong & hammer dogs, small log turner, gang flipper, (4) trucks, pantograph, FORANO hydraulic take ups, 60 lb rail x 90', controls in cab, 4'x6' cab, spare parts, s/n: 151389
  • POWERTEC 200 hp/1750 rpm DC drive motor, 132X1J, 235 RMS amps, 640 bus VDC, FALK 15.730:1 reducer, carriage spool w/FORANO M7HR 200 hp DC drive, THUNDERBYRD 350 kvar high performance capacitor
  • GE 50 hp/650-2080 rpm/240 volt spare installed DC drive w/HYDE 5089-24 reducer, GE 50 hp MG set, LLOYD controls

End Dogging Twin Band Resaw w/Chipping Heads
  • McDONOUGH 60" Temposonic positioned end dogging twin vertical band resaw, approx 125 hp, (2) CM&E 34LH Temposonic positioned chipping heads, 250 hp/1800 rpm, PAC KNIFE system, 28" saw face, both sides set, 4"-18" diameter x 6'-22' length capacities, 22' hydraulic Temposonic positioned centering rolls, 44' hydraulic driven end dogging chain w/feed thru slat chains, split outfeed rollcases, dual AB SLC 5/03 PLC w/(8) SAS/lineal positioners, SAS controls, (4) lasers w/rack, (2) AB size 5 RVS, SAS 120 hp hydraulic unit w/3 pumps, SAS 40 hp hydraulic unit, spare bandsaws, parts, twin band resaw s/n's: 72M258LTSDAS, 72M259LTSDAS, chipping heads s/n's: 0621, 0622

Edgers
  • 1991 UKIAH 8"x36" single splined bottom arbor gang edger, (2) TOSHIBA 300 hp/1780 rpm arbor drives, climb cut, clam shell opening, 25" saws, press rolls, chromed knurled feed rolls, 30 hp, min cant size 2-1/4"x2-1/2", max cant size 8-1/2"x15", 130 fpm, 6" #3 splined arbor, 26" max saw size, 25' powered infeed rollcase w/(9) 8-1/2"x59" rolls, 6' 5-strand jump transfer, 30' powered outfeed rollcase, (6) 10"x30" rolls, drive, saw glide system, (2) 300 hp starters, spare saws, parts
  • SCHURMAN 4"x54" single bottom splined arbor board edger w/4-saw setworks, GE 150 hp/1770 rpm arbor drive, chromed knurled feed thru rolls, press rolls, 17' powered infeed rollcase w/(6) 9"x59" rolls, 8-strand jump transfer, 5"x20' outfeed belt, drives, SCHURMAN/TRABON lube system, (3) LASER BLAZERS, 50 hp hydraulic unit, spare saws, parts
  • Approx 4"x48" board edger, TOSHIBA 100 hp/1760 rpm arbor drive, 3-saw setworks (not installed)

Trimmers
  • Individually motorized LH sawmill trimmer, cuts 16', passes approx 26', (9) 10 hp/3500 rpm air drop saws, zero saw, 12' 7-strand lugged feed thru transfer w/28" even end rollcase, 5' 7-strand infeed transfer w/carry over wheels, 8' 6-strand unscrambler, drive motors, PFS 30 hp hydraulic unit, KOYO DIRECT LOGIC 405 PLC, AB 3-section PLC, 5'x6' cab, spare saws, parts
  • MISSOULA individually motorized planer trimmer, cuts 16', passes 19', (9) 5 hp/3500 rpm air drop saws, 9' 8-strand lugged feed thru transfer, 21' 4-strand H78 infeed transfer, 42' 5-strand H78 green chain, 24"x21' outfeed transfer, spare saws, parts
  • Custom built line shaft planer trimmer, 30 hp, 14' trim, 18' pass, (6) saws, 8' 5-strand lugged feed thru transfer, 30' 3-strand H78 infeed transfer, 57' 3-strand H78 green chain, 22"x17' clean out belt transfer, spare saws, parts
  • Custom built 20' trimmer w/1' & zero saw (not installed)

Sorter
  • HEMCO series 45 computerized RH 21-bay sling sorter, set up for 4'-16', 22-1/2' between columns, 115' 5-strand lugged feed thru transfer, TOSHIBA 20 hp to RADICON reducer, 40' 8-strand lugged infeed transfer w/64" even end rollcase, 10' 8-strand unscrambler, (2) 57' 4-strand take away chains w/S-drive, 7.5 hp to FALK 45 rpm reducers, controls, electrics, STAR 24'-27'H x 40'W x 208'L all steel clear span building, job # 2284

Stacker
  • LSI 16' over end LH stacker w/COE sticker placer, (9) sticker pockets, 19'x52" lumber lowering rollcase, (4) lumber placing arms, 17' 4-strand C55D infeed transfer, 7' 5-strand 81XH infeed transfer w/42" even end rollcase, 8' 6-strand unscrambler, 52"x32' outfeed rollcase

Planers-Pineapple Feed Tables-Live Bridges
  • YATES AMERICAN A63 planer, 8"x15", (4) heads, (16) knives, 100 hp top, 50 hp bottom, 40 hp & 30 hp side heads, 25 hp feed drive, 5 hp hydraulic unit, top & left side chip breakers, pressure bar, top & bottom feed rolls, cutter head brake, (5) spare heads, knives, jointer bar, parts, s/n: 29149
  • 21' hydraulic dual pineapple feed table w/(5) 8"x30" rolls, hold over shoe, 25 hp hydraulic unit
  • 6' hydraulic driven live bridge w/(4) 11"x18" rolls
  • 16"x28' outfeed belt transfer
  • 36"x68" slowdown belt
  • YATES A20-12 planer profiler, 8"x15", (5) heads, (8) knives, 70 hp top, 35 hp bottom & side, 25 hp side, 35 hp top profile, 40 hp belt drive, top & bottom feed rolls, spare heads, knives, jointer bar, spares, s/n: 290A2
  • 18' belt driven single pineapple feed table w/(7) 5"x36" spiral rolls
  • 44" live bridge
  • 14"x56" speed up belt
  • NEWMAN M455 hydraulic single pineapple feed table (not installed)
  • 17' single pineapple feed table w/4' live bridge (not installed)

Tilt/Breakdown Hoists-Planer Blowers-Pallet Wrapper
  • 16' 4-arm hydraulic tilt hoist w/62"x74" travel arms, 20 hp hydraulic unit, 23' 4-strand H84 infeed transfer, 12"x20' sticker belt (YATES A63 planer)
  • 16' 4-arm mechanical breakdown hoist w/52"x62" travel arms, 10 hp, w/brake, 30' 3-strand H78 infeed transfer, sticker belt (YATES A20-12 planer)
  • 16' 5-arm mechanical tilt hoist w/52"x60" travel arms (not installed)
  • 72" planer blower, 125 hp (YATES A20-12 planer)
  • 48" planer blower, 75 hp, EMERSON/SAFTRONICS CSXI series soft start
  • Bander squeeze unit w/bump gate (not installed)
  • (30+) lumber carts
  • LANTECH SVS-80-LG LANRAPR stretch wrap machine w/48" pallet
  • IMCO 32"x52' radial stacker, 50 hp hydraulic motor
  • WHIRLWIND RH pneumatic chop saw

Kilns-Carts-Rail-Stickers-Dunnage
  • MOORE/COE 30'x55' double track direct fired kiln w/MAXON 1400 natural gas type 10,000 btu burner, 72"x36" combustion air fan, 60 hp, (11) 48" fans, 60 hp/550 rpm motors, DELMHORST moisture detector, FRANK data acquisition digital temperature system controls, AB 5-section MCC (installed in 2004)
  • MOORE 30'x106' double track direct fired kiln w/MAXON 1400 natural gas type 10,000 btu burner, 72"x36" combustion air fan, 60 hp, line shaft driven fans, 60 hp/550 rpm motor, FRANK controls, QUINCY 7.5 hp/23.8 cfm, 80 gallon, single phase tank mounted compressor (new compressor in 3/09)
  • 2500'+ of kiln rail
  • (60+) kiln carts, 48"x106" overall w/30"x72" centers
  • (3) kiln carts, 102"x52' overall w/48"x60" centers
  • (250,000+) kiln stickers, 3/4"x1-1/2"x48"
  • (400+) 6"x6"x8' lumber bunks
  • Large quantity of assorted mill ends & yard bunks

Hogs
  • MONTGOMERY 34HD40B0H B10 hog, TOSHIBA 200 hp, SIEMENS SIKO soft start SRW34 reduced voltage soft start, spare hammers, s/n: 1679
  • JEFFREY swing hammer pulverizer, size 36-24, B-3 armor plate (not installed), s/n: 8879

Chippers
  • KOCKUMS 58" 8-knife big mouth chipper, MARATHON 150 hp, 1"x5"x14" anvils, 3/8"x4"x16 3/8" knives, 4.75"x58" disc, 15" round log capacity, feed speed 450 fpm, 10,000 lb overall weight, horizontal infeed, top discharge, s/n: 059-242
  • BLACK CLAWSON 48" 6-knife chipper, 150 hp, side drop infeed, top outfeed (not in use), s/n: 3877

Chip & Surge Bins-Wig Wag
  • PEERLESS 62-unit hydraulic chip bin w/screw leveler, 7' cyclone, 15 hp hydraulic unit
  • CAROTHERS 42-unit hydraulic shavings bin w/screw leveler, 15 hp hydraulic unit
  • PEERLESS 30-unit hydraulic chip bin w/screw leveler, 15 hp hydraulic unit
  • 10-1/2'W x 12-1/2'L x 12'H live bottom surge bin
  • 9'W x 9'L x 12'H live bottom surge bin
  • RADER single hood wig wag chip loading station w/5 hp car hauling winch

Chip Screens-Blowers-Feeders
  • KOCKUMS KS88 8'x8' 2-deck chip screen, TOSHIBA 5 hp/1180 rpm, s/n: 078-091
  • PRECISION 55 5'x5' 2-deck chip screen, s/n: 146
  • ROOTS WHISPAIR 10"x30" blower, WESTINGHOUSE 100 hp, s/n: 44854
  • 8"x20" blower, GE 75 hp
  • SUTORBILT 8"x18" blower, AC 30 hp
  • 8"x16" blower, WESTINGHOUSE 75 hp, w/silencer
  • 8"x12" blower, 25 hp, w/silencer
  • 30"x30" chip feeder w/motor to shaft mounted reducer
  • (2) ARCHER 25"x25" chip feeder w/motor to shaft mounted reducer
  • ARCHER 20"x20" chip feeder w/motor to shaft mounted reducer
  • ROOTS 20"x20" chip feeder w/motor to shaft mounted reducer

Vibratory Conveyors
  • CARRIER BM24-100-FS 24"x100' vibratory conveyor, 4' fiberglass trough, 10' FINES drop out, 1" stroke, leaf spring type, RENS C220 metal detector, s/n: 17302
  • WEBSTER type FS FSM 18"x41' vibratory conveyor, 9/16" stroke, 565 rpm leaf spring type, s/n: 962-0913-1
  • VIBRA PRO BLS-241200F 3/16" (MS) 30', 5 hp, 24"x21' vibratory conveyor, 7/8" stroke, 400 rpm, leaf spring type, s/n: 1155
  • 24"x27' vibratory conveyor, leaf spring type (not installed)

Compressors-Dryers-Tanner Tank-Air Receivers
  • QNW 740B rotary screw compressor, 150 hp, air cooled, halon, 26781 hrs
  • QNW 490 rotary screw compressor, 100 hp, air cooled, halon, 22121 hrs
  • QNW 25 hp rotary screw compressor, tank mounted, air cooled, halon, 20168 hrs
  • WORTHINGTON 150 rotary screw compressor, 200 hp (not installed)
  • LEROI DRESSER rotary screw compressor, 75 hp (not installed)
  • SULLAIR 24KT Sulliscrew rotary screw compressor
  • QUINCY 7.5 hp tank mounted compressor, 80 gallon, 23.8 cfm, single phase (3 mos. old)
  • Assortment of tank mounted compressors to 20 hp
  • DELTEC PS110FHSP dual tower compressed air dryer, 200 psig, s/n: 14PS800 (new desiccant)
  • (3) SKF cartridge type direct in line air dryers (installed in 2009, 2007)
  • TANNER tank series 400 vaporizer
  • (2) 3'x8', 3'x6' air receivers

Chipping Cantor-Stud Machine
  • STETSON ROSS chipping canter w/60 hp top, bottom & side canting heads, 10' centering rolls, twin 18' infeed alligator chains, powered knurl feed thru rolls, chip feeder, control in cab, s/n: 5583
  • ROLLIES MACHINE WORKS stud harvester log processor w/dual approx 32" vertical husk saws, feed thru chains, 4" between saws, 16" outside saws, (2) vertical saw arbors w/(5) saws @ 2" spacing, 2-strand infeed transfer, outfeed chain to 2-strand transfer, clean out conveyor (no drives), s/n: C-118-157

Scales-Trailer Loader
  • FAIRBANKS 90-161A load cell scales, 50 ton x 20 lbs, 10'x70' concrete deck, FAIRBANKS DRO, EPSON printer
  • Approx 8000 lb capacity shop built trailer loader

Filing & Grinding Room Equipment
  • ARMSTRONG #6 LH bandsaw sharpener, s/n: 2312
  • ARMSTRONG #4 LH bandsaw sharpener, s/n: 12503
  • ARMSTRONG #4 LH stretcher roll w/anvils, welder, stand, s/n: 5718
  • ARMSTRONG 3-10 stretcher roll
  • WRIGHT 350 auto dual face grinder
  • WRIGHT 150HD face grinder
  • WRIGHT face grinder
  • (3) ARMSTRONG #16 circle saw sharpeners
  • IMW 240 guide grinder
  • (2) MICHIGAN 60" travel bed knife grinders, s/n's: 1680, 1277
  • STETSON ROSS travel bed side head grinder
  • STEHLE hydraulic auto side head grinder
  • CM&E slabber knife grinder
  • THOMPSON & HOE guide grinders
  • BARNHARDT wheel grinder w/power heads & remote control
  • (5) Babbit pots; quantity of babbit; babbit pour guides; anvils; jigs; molds; bandsaws; round saws; swages; shapers; 3"x12"x18" granite plate; (2) 60" insert tooth saws

Electrical
  • 2006 SIEMENS 2000 amp 4-section switchboard, 480Y/277 volts, 800, 500 & 200 amp switches, s/n: 19049G43-A00010-01
  • 2007 CH-EATON POWR-LINE PRL4 panel board, 800 amps, 480Y/277 volts, 800 amp adjustable trip breaker
  • ALLEN BRADLEY 7-section MCC w/(25) switches
  • ALLEN BRADLEY 4-section MCC w/(15) switches
  • ALLEN BRADLEY 3-section MCC w/(16) switches
  • ALLEN BRADLEY 2-section MCC w/(9) switches
  • GE 7700 line 6-section MCC w/(21) switches
  • SIEMENS 200 hp RVSS
  • EMERSON/SAFTRONICS CSXI series 100 hp soft start
  • (8) SAS lineal positioners
  • uantity of adjustable frequency drives & inverters, motors to 300 hp
  • WILLET LABEL JET LH210 labeler (new)
  • WILLET LABEL JET 2110-4 labeler

Machine Shop
  • 1995 ENCO 14"x45" quick change engine lathe, 22-1800 rpm spindle speeds, 2-1/2" bore hole, 3 & 4-jaw chucks, tool post, steady rest, tail stock, s/n: 111-1415
  • LODGE & SHIPLEY 20"x144" engine lathe, 9-500 rpm spindle speeds, 2-1/2" bore hole, 3 & 4-jaw chucks, tool post, steady rest, tail stock, s/n: 112265
  • LAGUN REPUBLIC FT4 vertical milling machine, 4 hp head, 350-4640 rpm spindle speeds, 11"x54" T-slot table
  • CINCINNATI No. 2M horizontal milling machine, 10"x52" T-slot table
  • EBERHARDT H.D. shaper
  • DAKE #202 arbor press
  • JET tool & die grinder
  • REMCO RS 905 horizontal metal cutting bandsaw
  • (2) 6" machinist vises
  • Assorted tooling

Miscellaneous Shop-Mill Supplies
  • Anvil; CLIMAX key mill; (2) WAGNER L722 stack probes w/L512 wood friendly digital moisture meters; (2) WAGNER MMI & (4) DELMHORST hand held moisture meters; PIONEER EX whole log metal detector; RENS discriminate whole log metal detector; FUJI KOH S302W auto level; AIE foot impulse sealer 600; (10ñ) MOTOROLA XTN series walkie talkies; (3) chain saws; WESTWARD hydraulic ram kit; truck floor jack; parts washer; (4) MILLER SRH 303 & 333 welders; oxy/acetylene sets; welding rod & supplies; GUILLOTINE M-5EB hydraulic shop press; RAMCO 50 ton shop press; horizontal metal cutting bandsaw; 3000 lb A-frame hoist w/2 ton chain hoist; IR T-30 2475 tank mounted compressor; RIDGID 16" drill press; DEWALT chop saw; COLL-O-CRIMP T-400 hose crimper & fittings; RIDGID 200 pipe threader; KAMAN filter cart; pressure washer; pipe vise SIGNODE AMT-58 strappers; plastic banding; carts; wheel pullers; jack stands; assorted power & hand tools; grease guns; (2) pallet jacks; welding shields; barrel pumps; cable winches; come-a-longs; ladders; vises; steel tables; chain hoists; hydraulic motors; pumps; propane tanks; rose buds; pipe bending equipment; assorted nuts, bolts & washers; parts bins & drawers; clean up tools; fire extinguishers; welding leads; safety supplies; bearings; sprockets; new & used chain; couples shafting; belts; filters; air hose; pullers; cams; cylinders; pipe fittings; assorted office furniture & equipment; large antique safe; approx 1000 gallon skid mounted fuel tank; (10ñ) lasers; starters; disconnects; AB; encoders; fuses; relays; transformers; capacitors; conduit & pipe fittings; rolls of wire; gearhead motors; trimmer motors; stators; motors to reducers; lights; heaters; monitors & cameras; fans; too much more to list

Buildings
  • 20' eaves-23' peak x 76' wide x 165' long all steel clear span sawmill building w/lights & sprinklers
  • STAR 16' eaves-18' peak x 80' wide x 100' long all steel clear span planer building w/14' eaves - 16' peak x 27' wide x 50' long all steel addition w/lights & sprinklers
  • 18' eaves-19' peak x 50' wide x 80' long all steel clear span bagger building w/lights & sprinklers
  • 14' eaves-20' peak x 50' wide x 80' long clear span planer pole building w/metal siding & roof, lights & sprinklers
  • STAR 23' eaves-26' peak x 30' wide x 70' long all steel clear span resaw building w/lights & sprinklers
  • 22' eaves-25' peak x 30' wide x 46' long clear span shavings building w/16' wide x 24' long off set, metal siding & roof
  • 18' eaves-20' peak x 57' wide x 61' long steel frame filing room building w/wood siding & roof
  • 14' eaves-16' peak x 18' wide x 80' long all wood machine shop
  • 8' eaves-13' peak x 24' wide x 36' long wood frame break room w/metal siding & roofing
  • Assortment of smaller wood buildings

Log & Lumber Transfer Equipment
  • 30' 5-strand CL02B chain log deck, S-drive w/motor to FALK 40 rpm reducer
  • 27' 4-strand H82 chain log deck, S-drive, ALLIS CHALMERS 10 hp, WESTINGHOUSE 38 rpm reducer
  • 12' 4-strand H82 chain log deck w/gearhead motor
  • (5) log rollcases to 30'
  • (5) log hauls to 100'
  • Transfers to 32'
  • (27) lumber transfers to 60'
  • (6) lumber conveyors to 140'
  • (20) belts to 75'
  • (8) rollcases to 60'

Rolling Stock
  • ELECTRO STACKER 2594, 4-wheel drive, 40 ton log stacker, CUMMINS NTC-400 diesel, 30-33-L4 tires, s/n: 2594-1166
  • 1998 JOHN DEERE 744H rubber tire log loader, diesel, log forks, 10' bucket, 8' slip bucket, 26.5 tires, s/n: DW744HX565337
  • 1975 FORD A64 rubber tire log loader, diesel, forks, 20.5-25 ties, enclosed cab, s/n: 3042
  • 1979 JOHN DEERE 770A motor grader, diesel, 10' mold board, side cutter, s/n: 07385-T
  • (2) 2001 CAT DP80 dual pneumatic tire forklifts, 17,500 lb capacity, CAT 3406 diesel engine, 157" 2-stage clear view mast, sideshift, 52" forks, s/n's: T32B-00029, T32B-00028
  • 1996 EAVES/FORANO E-155 dual pneumatic tire forklift, 15,500 lb capacity, CUMMINS B-230 diesel, 124" 2-stage mast, 54" forks, s/n: CE120180019609-1
  • 1998 TAYLOR THD-160 pneumatic tire forklift, 16,000 lb capacity, CUMMINS B-230 diesel, 150" 2-stage clear view mast, sideshift, 54" forks, s/n: S-C8-24931
  • 1998 TAYLOR TB160S single pneumatic tire forklift, 14,000 lb capacity, 16,000 lb capacity w/dual tires, CUMMINS B-230 diesel, 150" 2-stage clear view mast, sideshift, 56" forks, s/n: S-C1-19342
  • 1972 TAYLOR Y-16-BWO dual pneumatic tire forklift, 16,000 lb capacity, CUMMINS B-230 diesel, 150" 2-stage clear view mast, sideshift, 56" forks, s/n: S-35-9932
  • 1998 HYSTER H90XLS dual pneumatic tire forklift, 9000 lb capacity, propane, 206" 2-stage mast, sideshift, 48" forks, s/n: G005D10999V
  • 1991 NISSAN PH02A25V pneumatic tire forklift, 5000 lb capacity, gas, 137" 3-stage mast, sideshift, 48" forks, s/n: PH02-920504
  • 1989 HYSTER S40B solid tire forklift, 4000 lb capacity, propane, 130" 2-stage mast, 40" forks, s/n: B002D07576K
  • 1989 JLG 60H manlift, 60' boom height, 56' reach, 500 lb capacity, gas, 14-17.5 tires, s/n: 030891220
  • 1983 CASE 480LL tractor, 8' bucket, box scraper, diesel engine, ROPS cab, s/n: 9080082
  • 1994 INTERNATIONAL single axle water truck, DETROIT 466 diesel, 12-speed trans, 2000 gallon water tank, 11R-22.5 tires, 28035 miles
  • 1973 GMC single axle dump truck, VORTEC 475 gas, 5-speed trans, 17' box, 11R-22.5 tires, 21797 miles
  • 1980 PETERBUILT 128451-P T/A tractor, CUMMINS NTC400 diesel, EATON FULLER trans, wet kit, 73087 miles
  • 1979 INTERNATIONAL CARGO STAR 1810B single axle tractor, 400 gas, 5-speed trans, 2538 miles
  • 1968 CHEVROLET 2-wheel drive flatbed shop truck, gas, manual trans, LINCOLN SA-200 welder, air receiver tank
  • STANDARD STEEL WORKS approx 500 gallon single axle fuel trailer, 6'x5' oval tank w/1/3 hp pump, gauge, nozzle
  • 1983 IMCO 50' live bottom tandem axle trailer w/11R-24.5 tires

  • The 2008 CASE 420 skid steer loader w/bucket, diesel, 530 hours, s/n: N8MH85985 previously listed, will not be included in the auction
    •

TERMS & CONDITIONS
  • 10% BUYERS PREMIUM
  • PAYMENT: Full payment must be made by no later than 4pm, Wednesday, July 1
  • A 25% deposit is required by the close of business, auction day.
  • Cash, cashiers check, Master & Visa Cards, wire transfers only. Personal or company checks accepted ONLY with bank letter of guarantee.
  • Absentee bids accepted with 25% deposit
  • REMOVAL: No purchase may be removed during the auction unless otherwise announced by the auctioneer. Removal schedule announced on auction day.
  • Announcements made by the auctioneer at the time of sale take precedence over printed matter.
  • Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
  • Due to safety & insurance reasons, persons under 12 not admitted.

  • Washington Auctioneers License #1960

AIRPORT & LODGING INFORMATION
    Airport: Denver International Airport serves all major airlines
    Lodging:
  • Comfort Inn  307-721-8856
  • Hampton Inn  307-742-0125
  • Hilton Garden Inn  307-745-5500
  • Holiday Inn  877-863-4780
  • Super 8  307-745-8901

DRIVER DIRECTIONS
  • From east or westbound I-80, take the Snowy Range Road exit (#311).
  • Drive east on approximately 3/10 mile to to W Garfield.
  • Turn right onto Garfield and drive east approximately 4/10 mile to S Pine St.
  • Turn right and drive south on Pine approximately 6/10 mile to the auction site, located on the right.

WATCH FOR AUCTION SIGNS

FOOD SERVICE AVAILABLE AT THE AUCTION SITE



Home | About Us | Auction Schedule | Immediate Sales | Email Signup | Map | Past Auctions | Registration Form | Advanced Bid Overview | Terms & Conditions | Best of 2000-2004 Auctions



James G. Murphy Co.
Commercial / Industrial / Real Estate Auctioneers
P.O. Box 82160 - 18226 - 68th Ave. N.E.
Kenmore, Washington 98028
(425) 486-1246 or Toll Free 1-800-426-3008
Fax: (425) 483-8247

Oregon address & phone:
105 McNary Estates Dr. N
Keizer, OR 97303
phone: (503) 463-4444
fax: (503) 463-1554


Corporate Media Arts Group

Copyright©1997-2009 James G. Murphy Co.
All rights reserved worldwide