Click small pics to enlarge

Click HERE for more photos





ATLAS BOARDMILL

WEDNESDAY & THURSDAY, JANUARY 18 & 19 * 10AM EACH DAY
Preview 10am to 4pm, Tuesday, January 17
3074 W Seltice Way, Coeur d'Alene, ID

Past Auction held in 2006

Catalogs: Day 1 | Day 2 | X Lots

PDF Catalogs: Day 1 | Day 2 & X Lots

Advance Bid Center

Notice to Contractors & Dismantlers:
  • A required meeting will be held at 8am, Tuesday, January 17, at the mill site office.
  • $5 million liability insurance required.

ORDER OF SALE
    DAY 1
    SAWMILL, KILNS, BOILERS

    DAY 2
    PLANER MILL, ROLLING STOCK(1PM), KILNS, BOILERS, MECHANIC & ELECTRICIAN SHOPS, MILLWRIGHT SHOP, SPARES, INVENTORY

Log Cut Off Saw
  • 84" diameter insert tooth hydraulic log cut off saw, 75 hp, log clamps

Debarker
  • SALEM 35" 5-arm air seal ring debarker, (2) 60 hp AC ring drives, feed thru chain, 50 hp AC drive, pneumatic in and outfeed log hold down rolls, hydraulic ring bypass

Log Break Down (large side)
  • Carriage
  • ALBANY 48"x20' 3-knee linear positioning log carriage, TYRONE BERRY hydraulic shotgun carriage drive, (2) 150 hp pumps, setworks, hydraulic support unit

Head Rig
  • FILER & STOWELL 8' right hand mechanical strain head rig bandmill, 81X chain lumber clearing table, 13" wheel face, 1-1/4" thick top wheel, drive

Slabber
  • CM&E #34 right hand linear positioning 8-knife pre-slabber, ACT knife setup, 200 hp, hydraulic log turner

Log Breakdown (small side)
  • CM MACHINERY 20'x26" diameter log capacity C frame overhead end dogging log breakdown system, (2) 200 hp 6-knife linear positioning pre-slabber heads, (2) 200 hp 42" diameter linear positioning splined arbor vertical scragg saws, pop up log centering roll infeed with hydraulic drives, log stop and loader, 150 hp DC carriage drive, (2) 24"x25' outfeed slab belt conveyors w/hydraulic drives, hydraulic support unit, control booth, APPLIED THEORY setworks with ALLEN BRADLEY 5/40L, 5000 logic PLC's

Resaw
  • CAE 6' twin horizontal mechanical strain linear positioning bandmill system, 125 hp bandmill drives, 32" wide feed thru rollcase w/hydraulic drive, pneumatic/hydraulic lumber hold down feed rolls, hydraulic support unit, control booth, INOVEC setworks

Edgers
  • SALEM combination edger w/6"x30" gang side, 6"x30" shifting saw side, (3) shifting saws, stack cylinder setworks, 300 hp arbor, 15 hp, 5 hp split edger feed rolls, sawmist system, clamshell & swing away openings, 20' split roll infeed rollcase, positioning chains, shifting linebar, s/n: 74 53 666
  • 1987 SALEM 3"x48" splined top arbor board edger w/(3) linear positioning saws, 75 hp, hydraulic feed roll drive, sawmist system, 17' knurled roll infeed rollcase, positioning chains, hydraulic lumber positioning arms, outfeed rollcase, hydraulic edge pickers, hydraulic support unit, INOVEC setworks, s/n: 126643-84
  • 1996 TIMBER MACHINE TECHNOLOGIES TMT 4"x36" 2-head chipping edger, 6-knife left and right hand chipping heads, 27" diameter ring facing saws on heads, 125 hp, 1 head linear positioning, in and outfeed press roll modules, in and outfeed rollcases, hydraulic support unit, controls, electrics, lasers, s/n: 5005

Sawmill Trimmer/Sorter/Stacker Line
  • 1999 CAE NEWNES 20'x2" cut, 24' pass left hand line shaft sawmill trimmer w/feed thru lug chain transfer, end evening rollcase, minus fence
  • 1999 CAE NEWNES OPT-TTL20-01, 20' optimized laser trimmer scanner system, s/n: 99-0053-D0
  • 1999 CAE NEWNES grade reader, s/n: A-5053
  • 1999 CAE NEWNES lug loader
  • 1999 CAE NEWNES moisture detector w/(4) search coils
  • 1999 CAE NEWNES 6' minimum to 20' maximum 61-bin drop pocket computerized J bar lumber sorter, UHMW lined bins, UHMW take away chain transfer
  • 1999 CAE NEWNES 6' minimum to 20' maximum auto placement sticker stacker w/UHMW lined H78 rooftop chain infeed, lumber dealing and lumber stop arms, (9) auto sticker placers, auto sticker placement transfer, 5-arm hydraulic package hoist, 30' 6-strand H82 chain outfeed package deck, hydraulic support unit, PLC, frequency drive electrics, 48"x9'x20' package capabilities

Planer Trimmer/Sorter/Stacker Line
  • IRVINGTON MOORE 72, 20'x2" cut, 24'10" pass individually motorized air lift planer mill trimmer w/feed thru lugged chain transfer, in and outfeed end evening rollcases, minus fence, lug loader, s/n: 20369-11
  • LUCIDYNE TECHNOLOGIES Colorscan 200 grade reader
  • CLAUSEN 6-roll grade imprinter
  • WILLETT LABELJET 262 labeler w/NORDSON 3500V series glue system
  • LSI 230', 15-tray 6' to 20' capacity computerized lumber tray sorter w/gearhead tray drives, 45', 4-strand 6" belt outfeed tray unloading tipple
  • LSI 6' to 20' capacity overend planer mill stacker w/chain transfer infeed, lumber dealing arms, hydraulic package hoist, hydraulic support unit, outfeed package deck, TI 305 PLC electrics, 48"x9'x20' capabilities

Planer Lines
  • (2) YATES AMERICAN A63 6"x15" 6-head, 16-knife planer/matcher/profilers, DC feed roll drive, FRANKS electric controls, 14' bridges, 20' pineapple feed tables, s/n: B29202
  • (2) 25' 5-strand H82 chain planer line package decks, S-drive, 5-arm hydraulic tilt package breakdown hoist, 50" arms, 70" lift, hydraulic support units
  • (2) WAGNER 683 moisture detection system w(4) search coils
  • (2) 6' lumber slow down belts w/vari speed drives
  • (2) 20' 5-strand H78 rooftop chain grading lines
  • Quantity side and profile heads

Kilns
  • (2) WELLONS 17'x70' steam heated single track, line shaft, aluminum shell bolt together dry kilns, (3) zones per kiln, (10) line shaft fans, 60 hp
  • (2) WELLONS 17'x70' steam heated single track aluminum shell bolt together dry kilns, (3) zones per kiln, (7) 20 hp cross kiln fans
  • (6) 17'x70' cinderblock kilns, 60 hp line shaft fans, COE & MOORE graphs, WELLONS electrics, OMEGA temperature controls, aluminum doors
  • WAGNER stack probe moisture detector
  • Quantity 105" wide kiln carts, assorted lengths, 6' center to center on wheels, kiln rail

Boilers
  • CLEAVER BROOKS CB266-350 natural gas/oil package boiler, 150 psi mwp, 14,645,000 btu per hour gas input, 1045 gph oil input
  • YORK & SHIPLEY Steam-Pak SPH350N112082 natural gas package boiler, s/n: 71-6304H52286
  • YORK & SHIPLEY 1000 hp fire tube type field erected wood fuel fired boiler, 35,400 lb per hour, 150 psi mwp, s/n: NB14700
  • YORK & SHIPLEY 600 hp fire tube type field erected wood fuel fired boiler, 17,500 lb per hour, 150 psi mwp, s/n: 5836
  • STOKER FULID bed burner system
  • Deaerator, water make up, water treatment tanks w/pumps
  • PPC INDUSTRIES 11R-1220-2612 2-cell electrostatic precipitator, 39,000 cfm volume operating conditions, 550 degree operating conditions, 6 second treatment time, inlet loading 0.94 grains at operating conditions, outlet loading gr/act cv ft .023, efficiency 76.19%

Chip and Bark Processing
  • JEFFREY 56WB drop feed bottom discharge hammer hog w/drive, s/n: 12314
  • (2) PRECISION 66-18 66" 8-knife horizontal feed bottom discharge chipper, 150 hp drive, s/n: C2054
  • SUMNER #35 V-drum knife hog w/blower
  • WESTERN PNEUMATICS 1230-5111 rotary lobe blower w/air intake, silencer, drive
  • RADER PNEUMATICS 10"x30" 3100 125 hp rotary lobe blower
  • SUTORBILT 7"x21" 40 hp rotary lobe blower
  • RADER PNEUMATICS 25"x30" chip feeder
  • PMM 20"x20" chip feeder
  • WESTERN PNEUMATICS 20"x20" chip feeder
  • BURNS 60" 300 hp low pressure planer mill blower, 24" 30 hp low pressure blower
  • KOCKUMS CS30 10'x10' 3 deck chip shaker screen, s/n: 550312030364
  • WESTERN PNEUMATICS 8'x21'x7' high surge bin w/(4) auger clean outs
  • PEERLESS 42-unit hydraulic shavings bin
  • CARROTHERS 42-unit hydraulic shavings bin
  • PEERLESS 42-unit hydraulic chip bin
  • PEERLESS 30-unit hydraulic sawdust bin

Filing and Grinding Equipment
  • (2) ARMSTRONG #4 right hand bandsaw sharpeners w/clamps, stands, frequency drives, Shape Up wheel shapers, s/n's: 11673, 9953
  • ARMSTRONG #4 left hand band saw sharpener
  • ARMSTRONG #6 right hand bandsaw sharpener w/clamp, stand, frequency drive, Shape Up wheel shaper, s/n: 3497
  • ARMSTRONG #90 bandsaw equalizer, s/n: 16404
  • (2) ARMSTRONG #5 bandsaw stretcher rolls w/leveling blocks, welding clamps, s/n's: 17897, 1654
  • Babbitt guide milling machine
  • STETSON ROSS 372 side head grinder
  • JONES-ORTH side head grinder, s/n: 47508
  • TIMBERLAND MG bent knife grinder
  • Assortment of filing room parts and supplies

Air Compressors
  • QUINCY QNW751 150 hp rotary screw air compressor, s/n: 990295C
  • QUINCY QNW740B 150 hp rotary screw air compressor, s/n's: 870122
  • SULLAIR Sulliscrew 75 hp rotary screw air compressor
  • SULLAIR 25-100L 100 hp rotary screw air compressor, s/n: 003-55650
  • QUINCY 7-1/2 hp tank mounted air compressor
  • PNEUMATECH PE1500 1500 scfm heat reactivated regenerative air dryer, s/n: 9907-S131760 011749
  • PNEUMATECH PE500 500 scfm heat reactivated regenerative air dryer, s/n: 0203-S136986-030856
  • Air receiver tanks, air lines and valves throughout plant site

Electrical
  • WESTINGHOUSE 2000 kva 13200 volt wye to 480 volt wye 3 phase pad mount transformer
  • T&R 2000 kva 13200 volt delta to 480 volt delta 3 phase pad mount transformer
  • T&R and B&B 1500 kva 13200 volt delta to 480 volt delta 3 phase pad mount transformers
  • ITE 4000 amp 4-section metered switchboard w/(10) fused switches
  • GE 2000 amp 3-section metered switchboard w/3000 amp HPC switch, (3) fused switches
  • SIEMENS 2000 amp metered 2-station fused switchboard
  • SIEMENS 1500 amp metered 3-station fused switchboard
  • SIEMENS 1200 amp fused disconnect
  • SIEMENS switchboard w/800 amp, 400 amp fused disconnects
  • ALLEN BRADLEY 10-section, 50-station motor control center
  • ALLEN BRADLEY 8-section, 30-station motor control center
  • ALLEN BRADLEY 7-section, 29-station motor control center
  • ALLEN BRADLEY 6-section, 23-station motor control center
  • ALLEN BRADLEY 5-section, 20-station motor control center
  • ALLEN BRADLEY 3-section, 13-station motor control center
  • ALLEN BRADLEY 2-section, 10-station motor control center
  • ALLEN BRADLEY 2-section, 5-station motor control center
  • ALLEN BRADLEY 2-section, 5-station motor control center
  • SIEMENS/FURNAS 7-section, 30-station motor control center
  • (2) SIEMENS/FURNAS 7-section, 23-station motor control centers
  • SIEMENS/FURNAS 3-section, 5-station motor control center
  • CUTLER HAMMER 9-section, 25-station motor control center
  • IDM 30 hp, (3) IDM 25 hp, ALLEN BRADLEY 20 hp, MAGNETECH 15 hp, IDM 10 hp, (8) IDM 5 hp frequency drives
  • (2) TOSHIBA 200 hp solid state, (2) INERTIA SYSTEMS 200 hp solid state, (2) ALLEN BRADLEY size 5 solid state, WARD LENARRD 125 hp solid state, SAFTRONICS 125 hp solid state reduced voltage starters
  • Quantity pole mount and lighting transformers, assorted stand alone starters, disconnects, PLC's, installed conduit and wire throughout plant site

Buildings
  • 38'x300' all steel clear span bolt together sorter building w/attached 30'x175' all steel clear span bolt together green chain building
  • 40'x550' all steel clear span bolt together planer sorter building
  • 30'x265' all steel clear span bolt together lumber storage building
  • (2) 40'x60' all steel clear span bolt together cooling sheds
  • 28'x45' all steel bolt together package boiler building
  • 8900 square foot irregular shape steel bolt together planer building
  • 26'x160' 3-sided bolt together lumber storage building
  • 75'x600' wood frame clear span lumber storage building w/75' lam beams
  • 20'x100' 3-sided wood framed lumber storage building
  • 45'x60' wood framed electricians building
  • 30,000 square foot wood and steel framed irregular shape sawmill building
  • Quantity assorted wood frame buildings

Support equipment, tooling, inventory
  • SIGNODE M22VC44 banding machine
  • Large selection mill log decks, log hauls, chain transfers, chain and belt conveyors, vibratory conveyors including: WEBSTER 24"x100'; 18"x75'; 18"x48'; (2) 18"x35'; 18"x21'; 24"x40'; VIBRA-PRO 36"x38'; PLUS: 250' 5-strand 81X planer chain; 110' H78 4" roll top green chain; 30' 5-strand H82 package deck w/5 arm hydraulic tilt package breakdown hoist, 58" arms, 60" lift; 20 hp rip saw line w/scissor lifts; 20' rotary sort table; rail car chip loading facility; rail car tarp station; steel sticker racks; (15) 12' lumber stacking carts; 50"x1-1/2"x3/4" wood stickers; hydraulic support units, GREENLEE 555 bender; (2) RIDGID 400 power threaders; (2) RIDGID 700 hand threaders; tri stands; KALAMAZOO H9AWV horizontal metal cutting bandsaw; TOLUND 24" drill press; THERMAL DYNAMICS 5XR plasma cutter; (2) LINCOLN R3R400, MILLER Dialarc 250AC/DC, MILLER MP65E, LINCOLN CV300, LINCOLN 200 amp, LINDE CE300, LINCOLN SP135 welders; oxy-acetylene sets; GATES OMNI 21 crimp machine; GATES 707 crimp machine; HOMELITE LR1E 4400 gas generator; ORBIT 20" drill press; abrasive chop saw; double end grinders; floor jacks; tranny jack; engine stand; cherry picker; shop press; mag base drill; power tools; ladders; steel tables; self dumping hoppers; MCM and control wire; conduit fittings and pipe; fuses; breakers; PLC in and output modules; electrical test equipment; electrical motors; structural steel and much, much more

Rolling Stock
  • CATERPILLAR 980C articulated front end loader, power shift transmission, diesel, log forks, s/n: 63X7342
  • (3) CATERPILLAR 950 articulated front end loaders, power shift transmission, diesel, GP buckets, s/n's: 81J11921, 73J3973, 81J1816
  • PRIME MOVER LD50 front end loader, diesel, GP bucket, s/n: 452
  • CASE 580C 2x2 loader/backhoe, enclosed cab, s/n: 8971059
  • 1988 LINKBELT LS4300C crawler log loader, s/n: 4200F5439
  • CATERPILLAR 225 crawler log loader with grapple, s/n: 61X364
  • (3) CATERPILLAR V200BSTR 20,000 lb dual pneumatic forklifts, 3208 diesel, 3 speed transmission, side shift, enclosed cabs, s/n's: 68Y01226, 68Y01169, 9AF00130
  • CATERPILLAR V200B 20,000 lb dual pneumatic forklift, 3208 diesel, 3 speed transmission engine, side shift, enclosed cab, s/n: 1DK00357
  • HYSTER H190XL 19,000 lb dual pneumatic forklift, PERKINS 6 cylinder diesel, side monotrol pedal, enclosed cab, s/n: E007D01859R
  • (4) CATERPILLAR V180B 18,000 lb dual pneumatic forklifts, 3208 diesel, 3 speed transmission, side shift, s/n's: 68Y00960, 68Y00610, 68Y00607, 68Y00987
  • CATERPILLAR V130D 13,000 lb pneumatic forklift, CUMMINS 43T3489 diesel, enclosed cab, s/n: 60W00582
  • (3) ALLIS CHALMERS CL80 8000 lb HRT forklifts, propane, s/n's: 17310432, 17310434,17309128
  • HYSTER H70BCS 7000 lb HRT forklift, propane, side shift, s/n: C004D02605X
  • HYSTERS60E, S60 6000 lb HRT forklifts, propane, s/n's: C4D5025A, C4D5497B
  • ALLIS CHALMERS C60LC 6000 lb HRT forklift, propane, s/n: ACA71263
  • ALLIS CHALMERS CL60 6000 lb HRT forklift, propane, s/n: 17309113
  • CATERPILLAR DP40 4000 lb pneumatic forklift, diesel, side shift, s/n: 3CN00326
  • TOYOTA 42-4FG25 5000 lb pneumatic forklift, propane, side shift, s/n: 404FG25-23823
  • ELGIN WHITE WING dual driver sweeper, JOHN DEERE diesel, (2) side brushes, roller brush
  • MASSEY FERGUSON 240 tractor, diesel, gp bucket, PTO, s/n: 010232
  • 1970 FORD F800 dump truck
  • 1971 FORD F250 8' flatbed
  • ACE 6000, 1000 gallon spill containment fuel tanks

TERMS & CONDITIONS
  • 10% BUYERS PREMIUM
  • PAYMENT: Full payment must be made by no later than 4pm, Friday, January 20.
  • A 25% deposit is required by the close of business, each auction day.
  • Cash, cashiers check, Master & Visa Cards, wire transfers only. Personal or company checks accepted ONLY with bank letter of guarantee.
  • Absentee bids accepted with 25% deposit
  • REMOVAL: No purchase may be removed during the auction unless otherwise announced by the auctioneer. Equipment removal schedule announced on auction day.
  • Announcements made by the auctioneer at the time of sale take precedence over printed matter.
  • Auctioneer reserves the right to sell accessories, parts or attachments on a separate and/or aggregate basis.
  • Due to safety & insurance reasons, persons under 12 not admitted.

  • Washington Auctioneers License #48

DRIVER DIRECTIONS
  • From east or westbound I-90, take the City Center/Northwest Blvd exit(#11).
  • Drive south on Northwest Blvd approximately 1/10 mile to Seltice Way.
  • Turn right and drive west on Seltice Way approximately 1.1 miles to the auction site, located on the left.

WATCH FOR AUCTION SIGNS

FOOD SERVICE AVAILABLE AT THE AUCTION SITE


LODGING
    AmeriTel Inn208-665-9000
    Best Western208-765-3200
    Super 8208-765-8880
    La Quinta Inn208-765-5500


Home | About Us | Auction Schedule | Immediate Sales | Email Signup | Map | Past Auctions | Registration Form | Advanced Bid Overview | Terms & Conditions | Best of 2000-2004 Auctions



James G. Murphy Co.
Commercial / Industrial / Real Estate Auctioneers
P.O. Box 82160 - 18226 - 68th Ave. N.E.
Kenmore, Washington 98028
(425) 486-1246 or Toll Free 1-800-426-3008
Fax: (425) 483-8247

Oregon address & phone:
105 McNary Estates Dr. N
Keizer, OR 97303
phone: (503) 463-4444
fax: (503) 463-1554


Corporate Media Arts Group

Copyright©1997-2005 James G. Murphy Co.
All rights reserved worldwide